Delhi Development Authority - Delhi

39832676 construction of under ground reservoir ( ugr ) in block b, sector 26 at rohini phase iv.sh:sitc of clear water booster pump set and allied accessories at ugr sector 26 rohini ; 1 supply, installation, testing & commissioning of horizontal split casing centrifugal pump set with bronze impeller directly coupled through flexible coupling with tefc squirrel cage induction motor of suitable rating for operation on 415 volts, 3 phase, 50 hz ac supply, mounted on common m.s channel base frame complete with foundation bolts, nuts, washers, coupling guard, pressure gauge 100mm dia with copper tubing, brass stop cock, water drain pipe of suitable size and length, required size of g.i taper and anti vibration mounting pads, rcc foundation ( 1:2:4 ) etc. complete as per specifications attached. the pump shall be capable to perform the following duties: a ) discharge : 118.8 m³ / hourb ) head: 26 m c ) type of liquid :clear waterd ) r p m : 1450 2 supplying, installation, testing and commissioning of sewage submersibledrainage pump of 300 l / min discharge of water at 10 m head having solid handling capacity of 35mm complete with base plate and all accessoriessuitable for operation on 220 volts, single phase50hz., a.c. supply complete with starter for automatic operation i / c water level sensing device, inter connection, and submersible cable etc. complete as reqd. 3 supplying and installation of following size m.s black pipe including m.s flanges duly screwed and welded on both ends of pipe, bend, tee, nipple rubber gasket, g.i nuts, bolts and washers, support etc. complete as required.a. ) 150 mm dia ( heavy c class ) conforming to is:1239 part1 ( 2004 ) with upto date amendment. 4 supplying and installation of following size m.s black pipe including m.s flanges duly screwed and welded on both ends of pipe, bend, tee, nipple rubber gasket, g.i nuts, bolts and washers, support etc. complete as required. b. ) 100 mm dia ( heavy c class ) conforming to is:1239 part1 ( 2004 ) with upto date amendment. 5 supplying and installation of following size m.s black pipe including m.s flanges duly screwed and welded on both ends of pipe, bend, tee, nipple rubber gasket, g.i nuts, bolts and washers, support etc. complete as required. c. ) 50 mm dia ( medium b class ) conforming to is:1239 part 1 ( 2004 ) with upto date amendment. 6 supplying and fixing of cast iron double flanged sluice valve pn 16 conforming to is:14846, rising spindle type of following size: complete with nuts, bolts, washers, rubber insertions, necessary support, hand wheel including painting and testing etc completerequired as per technical specification attached. a. ) 100 mm dia 7 supplying and fixing of cast iron double flanged sluice valve pn 16 conforming to is:14846, rising spindle type of following size: complete with nuts, bolts, washers, rubber insertions, necessary support, hand wheel including painting and testing etc completerequired as per technical specification attached.b. ) 150 mm dia 8 supplying and fixing of cast iron double flanged non return valve pn 16 confirming to is: 5312 without by pass arrangement of following size complete with nuts, bolts, washers, rubber insertions necessary support, including painting and testing etc, as required. a. ) 100 mm dia 9 supplying and fixing of cast iron flanged foot valve confirming to is: 4038 of following size complete with nuts, bolts, washers, rubber insertions including painting and testing etc, as required. a. ) 200 mm dia 10 supply, installation, testing and commissioning of mild steel double flanged dismantling joints of pressure rating pn16 of the following sizes complete withginuts, bolts, washers, rubber insertions, painting & testing etc. as required.a. ) 100 mm dia 11 supply, installation, testing and commissioning of mild steel double flanged dismantling joints of pressure rating pn16 of the following sizes complete withginuts, bolts, washers, rubber insertions, painting & testing etc. as required.b. ) 150 mm dia 12 supplying and fixing of bronze globe valve of 50 mm dia in the existing pipe complete with rubber insertions, teflon tape accessories including painting and testing etc, as required. 13 sitc of floor mounted free standing type l.t. cubical main feeder pillar duly compartmentalized ( outdoor type ) made out of 2 mm thick ms crca sheet, 7 tank process powder coated, with 4 nos. x 600 mm long legs made of m.s angle iron of size 40 mm x 40 mm x 5 mm thick along with frame & legs suitably grouted in foundation i / c connection inter connection of the accessories mounted there on with suitable size of copper wire / strip with thimble / lugs, earthing the body of the feeder pillar suitable for operation on 415v, 3 phase, 50hz ac i / c supply & fixing of the following items and as per technical specification enclosed. a ) 250 a, 50ka, fpmccb ( ics= icu ) 1 no ( incomer ) b ) 63 amp tp mccb, 25 ka breaking capacity= 5 nos. ( 4 nos. for pump set+1 no. for iei ) outgoingc ) 32 amp dp mcb c series 4 no.d ) volt meter ( 0 500v ) 96 sq.mm with selector switch – 1 sete ) amp meter ( 0 100a ) 96sq.mm with selector switch & 100 / 5 amp ratio cts – 1 setf ) led type ryb phase indicating lamps, on, off, trip indicating lampsh ) 6 amp sp mcb – 1 no.i ) 3 phase 440 volts power shunt capacitor 7 kvar ( with 63 amps tp mcb ) including all accessory complete 4 setsj ) single phase preventerk ) star delta starter suitable for item no.1 load 4 set.l ) 400 amp, 4 strip sleeved aluminium busbar – 1 setm ) danger notice plate – 1 no.n ) 6 pin 15 a switch / socket outlet 1 seto ) lighting inside the feeder pillarfor all mccb ( ics= icu ) . outgoing mccb of motor shall be of motor grade.note: foundation height of 750 mm duly plastered & finishedhaving top outer edges 30 cm beyond all round the edges of 40x5 angle iron frame shall be made as per site requirementfor which nothing extra shall be paid. 14 supplyingof the following sizes of xlpe insulatedaluminium conductor armoured cable of 1.1 kv grade confirming to is: 7098 part 1 with upto date amendment. a. ) 3.5 c x95 mm² 15 supplyingof the following sizes of xlpe insulatedaluminium conductor unarmoured power cable of 1.1 kv grade confirming to is: 7098 part 1 with upto date amendment.a. ) 3 c x50 mm² 16 supplyingof the following sizes of xlpe insulatedaluminium conductor unarmoured power cable of 1.1 kv grade confirming to is: 7098 part 1 with upto date amendment. b. ) 4 c x16 mm² 17 supplyingof the following sizes of xlpe insulatedaluminium conductor unarmoured power cable of 1.1 kv grade confirming to is: 7098 part 1 with upto date amendment. c. ) 3 c x4 mm²flat cable 18 supplyingof the following sizes of xlpe insulatedaluminium conductor unarmoured power cable of 1.1 kv grade confirming to is: 7098 part 1 with upto date amendment. d. ) 3 c x4 mm² 19 supplying and installing following size of perforated pre painted m.s. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, paintingsuspenders etc as required.a. ) 300 mm width x 50 mm depth x 1.6 mm thickness 20 supplying and installing following size of perforated pre painted m.s. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, paintingsuspenders etc as required.b. ) 100 mm width x 50 mm depth x 1.6 mm thickness 21 supplying and installing following size of perforated painted with powder coating m.s. cable trays bends with perforation not more than 17.5%, , joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required.a. ) 300 mm width x 50 mm depth x 1.6 mm thickness 22 wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm frls pvc insulated copper conductor single core cable etc. as required. group b 23 wiring for light / power plug with 2x4 sq. mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit alongwith 1 no. 4 sq. mm frls pvc insulated copper conductor single core cable for loop earthing as required. 24 supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.a. ) 6 pin 15 / 16 a socket outlet 25 wiring for circuit / submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface / recessed steel conduit as required. a. ) 2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire 26 supplying and fixing of 90 watt led street light luminaire made up of pressure die cast aluminium alloy housing withip 66, ik07 protection, system efficacy>110 lm / w lumens, integral electronic driver with apfc, thd<10%, output short / open circuit protection, surge protection upto 10 kv ( with external spd ) phase to phase ( 440 v ) / over voltage protection & other safety test as per is 15885 part 2 / sec 13. cri>70, cct 5700 k suitable to operate on 240 v, 50 hz, a.c supply. installation on bracket of 1 mtr lengthmade of suitable dia gi pipe on surface / in recess with all required accessories including connections, testing etc. complete as required with minimum 5 years guarantee / warranty 27 supplying, installation, testing and commissioning of 24 watt prewired led batten with aluminium housing and integrated electronic driver efficiency>88%, inbuilt surge protection of 2.5 kv, cri>80, cct 6500 k, thd<20, lumen output > 100 lm / wattcomplete with all accessories directly on ceiling / wall suitable for operation on 230v, 50 hz ac supply including connection with 1.5 sq.mm frls pvc insulated copper conductor , single core cable and earthing etc. as required with minimum 2 years guarantee / warranty. 28 supply of celling fan of 1200 mm sweep sizes with minimum 226 m3 / hr. air delivery operating on single phase 50 hz, 230v, ac supply, complete etc. as required. 29 supplying and fixing extra conduit down rod of 20 cm length g.i. pipe 15 mm dia, heavy gauge including painting etc. as required. ( note : more than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored ) 30 supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 31 supply of exhaust fan operating on single phase50 hz230 volt ac supply of 300 mm sweep size min 1600 m3 / hr. air delivery at rated speed 1380 rpm in metal body, bird guard to protect the fan in running condition, guarantee / warranty of 2 years with complete kit & required accessories for installation etc as required 32 installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. up to 450 mm sweep. 33 extra for fixing the louvers / shutters complete with frame for exhaust fan of all sizes 34 numbering of ceiling fan / exhaust fan / fluorescent fittings / led fitting / led street light fitting etc as required. 35 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) . a. ) 12 way , double door 36 supplying and fixing 5 a to 32 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. a. ) single pole 37 supplying and fixing 5 a to 32 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required.b. ) double pole 38 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. 39 supplying and laying 25 mm x 5 mm g.i strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with g.i. nut, bolt, spring, washer etc. as required. ( jointing shall be done by overlapping and with 2 sets of g.i. nut bolt & spring washer spaced at 50mm ) 40 providing and fixing 25 mm x 5 mm g.i. strip on surface or in recess for connections etc. as required. 41 providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required. 42 supplying and replacement of insulation mat for electric purpose confirming to is 15652 / 2006, duly isi marked with anti skid abrasion size 1 mtr.x 2 mtr., b class, thickness 2.5 mm for 11 kv working voltage. 43 sitc of is: 15683 marked powder stored pressure type portable fire extinguisher with is: 14609 marked abc powder ( m.a.p 90% ) capacity 6 kg complete with squeeze grip release valve discharge pipe locking arrangement pressure gauge operation manual bracket with two screws & sleeves etc. complete as required 44 sitc of co2 ( carbon dioxide ) fire extinguisher isi marked confirming to is: 15683. capacity 4.5 kg complete with delivery hose horn, locking arrangement, operation manual, bracket with two screw and sleeve etc. complete as reqd....

Delhi Development Authority - Delhi

39808056 maintenance of completed schemes under na ii ( hort.zone ) .sh: providing & fixing of decorative lights for work of cafeteria at baansera near sarai kale khan.; 1 providing & fixing i / c testing & commissioning of bollard light 6 10 w in 600 mm height.fitting is made of corrosion resistant zinc plated erw ms tubular sections with die cast base. diffuser is made of impact resistant pmma specially design for efficient lighting. colour tolerance , 3 scdm to avoid colour deviation. nanoceramic surface conversion, resistant to corrosive environment. luminaire primarily coated with epoxy resin and top coated with uv stabilized powder coat. all exterior parts are made of stainless steel.silicone rubber gasket are provided for water protection. light output of source is more than 110lm / watt, cri>70, operating voltage 140 270v. branded leds of osram / cree / seoul and fulham / meanwell / osram or equivalent constant voltage / current driver withthd < 10% power factor>0.9. the cct of led will be 3000k or as decided by engineer in charge and fixture color will be black as required by the project. fitting is ip65 with proper thermal management for longer life of fixture. fitting is complete in all aspects with all accessories i / cfoundation bolt.vak model no: vak bl qua 60 s 06 or similar superior make. 2 providing & fixing i / c testing & commissioning of surface mounted led linear fixture with elliptical beam ( 20 degrees x 50 degrees ) with wattage not more than 10w, 1000 mm length cct 3000k or as decided by engineer in charge, cri>80. leds in fixture should be of macadam step 3 or less. fixture to be made of 6063 aluminium alloy housing. silicone clear gasket, ss fasteners. mechanical resistance ik06, ip65 tempered toughened glass . this luminaire contains built in led modules. lifespan of the luminaire should be more than 50, 000 hours at 40°c. driver efficiency >80% ( integral ) , power factor >0.90, thd<20%, surge protection 3kv. vak model no: vak ww blo f 10 s 10 or similar superior make. 3 providing & fixing i / c testing & commissioning ofsurface mounted linear led strip light for seamless illuminance. led strip are protected with ip 65 protection and placed in a continuous row on the encapsulated pmma tube of 5mtr.it consist of 2835 smd package with a thermal tape of high thermal convection factor, system power: 5w / metre, luminous flux 350lm, colour temperature of 4000k or as decided by engineer in charge, macadam 5, diffused lighting, constant voltage driving circuit. vak model no: vak cv inl cove i6 5 or similar superior make.lifespan of the luminaire should be more than 50, 000 hours at 40°c. 4 providing & fixing i / c testing & commissioning ofground recessed ledround fixture with wattage not more than 9w, cct 3000k or as decided by engineer in charge, cri>80. leds in fixture should be of macadam step 3 or less. fixture to be made of die cast aluminium alloy housing. 316 grade stainless steel front ring. silicone clear gasket. ss fasteners.mechanical resistance ik06, ip protection 67. toughened clear glass diffuser of 8mm thickness with optical reflector to reduce glare. this luminaire contains built in led modules. led modules are engineered with branded osram or equivalent make led andequivalent constant current driver , lifespan of the luminaire > 50, 000 hours at 40°c. vak model no: vak gb eth rd r09 or or similar superior make.lifespan of the luminaire should be more than 50, 000 hours at 40°c. 5 providing & fixing i / c testing & commissioning ofground embedded led linear fixture with diffused beam in 10w / mtr. fixture is linear path marker with wattage not more than 10w / m in 1000mm length cct 3000k or as decided by engineer in charge, cri>80.leds in fixture should be of macadam step 3 or less. fixture to be made of 6063 aluminium alloy housing with leds in series jacketed by an encapsulated tube.mechanical resistance ik06, ip67 protectionconstant voltage driving circuit with efficiency >80% ( external ) , power factor >0.90, thd<20%. vak model no: vak gb mon line r10 or or similar superior make.lifespan of the luminaire should be more than 50, 000 hours at 40°c. 6 providing & fixing i / c testing & commissioning spot light in 20w for landscape lighting.fitting is made of corrosion resistant die cast aluminium with led wattage not more than 10w, cct 3000k or as decided by engineer in charge, cri>70. leds in fixture should be of macadam step 3 or less. fixture to be made of 6063 aluminium alloy housing. this luminaire contains built in led modules. driver efficiency >80% ( integral ) , power factor >0.90, thd <20%, surge protection 3kv. all exterior parts are made of stainless steel. silicone rubber gasket are provided for water protection. light output of source is more than 110lm / w.fitting is ip65, wired with branded osram or equivalent make led andequivalent constant current driver. proper thermal management for longer life of fixture. lifespan of the luminaire should be more than 50, 000 hours at 40°c.. vak model no: vak sl lun spike g10 or or similar superior make....

Delhi Development Authority - Delhi

39253671 maintenance of scheme under nazul a / c ii rohini zone.sub head: improvement of swarn jayanti park by providing signages at sector 10, rohini. ; 1 taking out and re fixing retro reflective 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type iii of astm d 4956 01 as approved by engineer in charge, letters, borders etc. as per irc : 67 2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class ii of astm d 4956 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. the rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer incharge. ( structural frame work including m.s. plate to be provided separately. rectangular area of the sheet only shall be measured for payment ) .a ) overhead informatory road signage. 2 manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type iii of astm d 4956 01 as approved by engineer in charge, letters, borders etc. as per irc : 67 2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class ii of astm d 4956 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. the rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer incharge. ( structural frame work including m.s. plate to be provided separately. rectangular area of the sheet only shall be measured for payment ) .a ) overhead informatory road signage 3 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :a ) one or more coats on old work. 4 painting with synthetic enamel paint of approved brand and manufacture to give an even shade :a ) two or more coats on new work 5 steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. a ) in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 6 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level :a ) 1:2:4 ( 1 cement : 2 coarse sand ( zone iii ) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources ) . 7 providing and fixing stainless steel ( grade 304 ) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i / c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. ) ....

Public Works Department - Delhi

39125455 providing and fixing road furniture items on various roads under pwd division south west road i during 2023 24 sub division v new delhi. 1 providing and fixing glow studs of size 100x20 mm made of heavy duty body shall be moulded asa ( acrylic styrene acryloretrite ) or hip ( high impact polystyrene ) or abs having electronically welded micro prismatic lens with abrasion resistant coating as approved by engineer in charge. the glow stud shall support a load of 13635kg tested in accordance with astm d4280.the slope of retro reflective surface shall be 35 ( + / 5 ) degrees to base .the reflective panels on both sides with at least 12cm of reflective area up each side. the luminance intensity should be as per the specification and shall be tested as described in astm i: 809 as recommended in bs: 873 part 4 :1973. the studs shall be fixed to the road surface using the adhesive conforming to is, as per procedure recommended by the manufacturer complete and as per direction of engineer in charge. 2 providing and fixing post delineators made of abs round body fitted with 2 nos 100 mm dia high reflective reflectors and mounted on ms pipe of 65 mm dia duly powder coated anti rust and anti theft steel to be installed as per direction of engineer in charge. 3 providing and fixingpvc flexible pu orange spring post, for road safety, 750 mm, 1000 mm as per direction of engineer in charge. rate shall include all taxes, loading, unloading and carriage to pwd store / site as per direction of engineer in charge. ( nothing extra shall be paid on any other account ) 4 providing and fixing of flexible medan markers as per irc 79:2019 which shall be made of combination of tough, high impact resistant molded thermoplastic body along with florescent yellow color retro reflective type xi sheeting with minimum exposed reflective area 90 cm square and with rebound property. the reflective sheeting should confirm to type xi florescent yellow sheeting as per irc 67 2012 and astm d4956 11. the flexible median marker shall have overall height of minimum 180 mm, width of minimum 120 mm & body thickness of medium 6.5 mm and shank depth of minimum 30mm & dia of shank shall not be less than 18 mm. the retro reflective sheeting shall be on both sides of the flexible median marker and shall be edge protected with no exposed edges which will prevent edge lifting, vandalism, sheeting damage, etc. the edge of sheeting should not come out easily by putting nails, sharp objects etc. the logo of the manufacturer shall be impressed on either side of the body. the flexible median marker shall be tested for rebound ability and tensile test from government laboratory as per requirement of irc 79 2019. 5 providing & fixing solar stud made from dark eye make pelli stud made of abs material having high wear resistance & impact strenght to bear havy loads weight is 58 gms. available in yellow & white colours. made from aluminium alloy and pc construction. solar powered by monocrystal solar panel. type of battery: one high capacity ni cd rechargeable battery view distance: approximate 1000 mtrs. leds 010 mm, 3 pieces each side and total 6 pieces are used for high brightness of diffierent colours back up 12 hours of continuous lighting at night. mounted on concrete or muddy ground. water proof & hardness tested. available in red & amber colours, having width 122.5 mm and lenght 132.5 mm and height 55 mm having stap dia 26 mm, as per direction of engineer in charge....

Military Engineer Services - Delhi

38896005 tender for repair / replacement of flooring, walling and misc works in sncos mess, airmen billet under hq wac age b / r i of ge ( af ) subroto park. 1 taking downframe or chowkhats ( w / o taking off shutter from the frame ) of any description exc. 1.50 sqm and not exc. 4.00 sqm each incl necessary repair to opening with cm 1:4 complete all as specifiedand directed. 2 taking downframe or chowkhats ( w / o taking off shutter from the frame ) of any description notexc. 1.50 sqmeach complete all as specified and as directed by engineer in charge. 3 taking down door shutter of any descriptionexc. 1.0 sqm but n exc 2.0 sqm each complete all as specifiedand directed. 4 m&l for two coats synthetic enamel paint over a coat of red oxideprimer on new steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of surfaces complete all as specified. 5 supply and fixing windows / ventilators fabricated from 0.60mm thick rollformed section made of galvanisedsteel powder coated ( base steel as per is 513d quality ) galvanised as per is 277 with zinc of 120gm / sqm .windows / ventilators having frame suitable fordual shutter i.e. inner and outer shutter with grill, glazed and wire mess shutter and all fitting, fixtures accessories incl6mmx12mm flat ironwith 10mm square bar m.s. grills complete as specified and shown in drawing no ceaf / std 191 / 2014, sheet 1 / 2 & 2 / 2 dated 11.12.14 ( 4000 series ) including taking down existing windows / ventilators of any description. 6 supply and fixing windows / ventilators fabricated from 0.60mm thick rollformed section made of galvanisedsteel powder coated ( base steel as per is 513d quality ) galvanised as per is 277 with zinc of 120gm / sqm .windows / ventilators having frame suitable forsingle shutter with grill, glazed shutter and all fitting, fixtures accessories incl 6mmx12mm flat ironwith 10mm square bar m.s. grills complete as specified and shown in drawing no ceaf / std 191 / 2014, sheet 1 / 2 & 2 / 2 dated 11.12.14 ( 3000 series ) including taking down existing windows / ventilators of any description. 7 hacking out old broken glass ( any thickness, size, quality or description ) from wooden / steel / aluminium framesglazed with putty or fixed with bead. ( old bead to be reused to fix glass ) complete all as specifiedand directed by engr in charge. 8 supply & fix sheet glass 4mm thick of selected quality n exc. 0.5 sqm each fixed to steel frame work with oil puttycomplete all as specifiedand directed by engr in charge. 9 s&f 4mm thick frosted floatglass and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specifiedand directed by engr in charge. 10 s&fstainless steel 304 grade wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed to window / door framecomplete all as specifiedand directed by engr in charge. 11 s&fin repair stainless steel 304 grade wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed to window / door framecomplete all as specifiedand directed by engr in charge. 12 s&f factory made solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet reinforced with mild steel square tube completeall asspecified and directed. 13 s&f in frame at site factory made solid pvc moulded door shutter30mm thick with 2, 4 or 6 raised pannels design with 2mm thick moulded pvc sheet on front faceand 2mm plain colour pvc sheet on back face of particle board core as per specification & drawing. 14 s&f framed work as in doors chowkats or gates of angle iron or other section with gusset plates, rails braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel handing doors fittingscomplete all as specified and directed. 15 s&f 30 mm thick flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides complete all asspecified and directed. 16 s&f 2nd class hw glazed and skeleton 35mm thick shutters, open rebated and prepared to receive glass gauze etc ( with out sash bars ) edges of framing plain, chamferedor rounded, fitted with cut and mitred beads for securing glass. gauze etc complete all asspecified and directed. 17 taking down of old unserviceable cupboard incl all fixture and fittings. note : for measurement superficial area in elevation will be measured only. 18 s&f factory made18 mm thick pre laminated pvc celluca ply for cup board shutters including provision of shelves, partiations, fixed with steel screws and solvent cement adhesive including 1mm thick lipping all around the edges complete all as per manufactured instructions. the celluca ply shall be manufactured by an iso9000 certified company and celluca ply density shall not less than 600 kg / cum. 19 s&f continous piano hinges, mild steel, bright finish or electrogalvanised of width of flap 30mm 20 m &l for125 mm magnetic catches with brass body and striking plate including letting in and fixed. 21 s&f of 125 mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws 22 m&l for two coats of synthetic enamel paint over a coat of pink primer on new wood surfacecomplete all as specifiedand directed. 23 s&f 100 mm long butt hinges medium weight cold rolled mild steel alloy with galvanized complete all as specifiedand directed. 24 s&f 150 mm long aluminium door handle, cast type, anodized complete all as specifiedand directed. 25 s&f 100 mm long aluminium handles, cast type, anodised complete all as specifiedand directed. 26 s&fof 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specifiedand directed. 27 s&f of 75 mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specifiedand directed. 28 s&f door stopper of aluminium, alloy body and tongue with hard drawn steel spring fixed in floors of 140 mm overall length of cover plate complete all as specifiedand directed. 29 s&f 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specifiedand directed. 30 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises complete all as specifiedand directed 31 m&l for pcc 1:2:4 type b 1 ( 20mm graded aggregate ) , 25mm thick as in sub base to the tile flooring complete all as specified and directed. 32 m&l for non skid ceramic colouredtiles 7 to 8 mm thick ( square / rectangular ) area of each tiles exc 0.11 sqm but n. exc 0.18 sqm, in floors or dado etc set and jointed in neat cement slurry and pointed in coloured cement to match over 15 mm thick screed bed or bedding layer in cm ( 1:4 ) complete all as specified and directed. 33 m&l forvitrified double chargetiles 8 to 10 mm thick ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in floorsetc, set and jointed in neat cement slurry and pointed in white or coloured cement to match etc over 15 mm th screed in cement mortar 1:4 complete all as specified and as directed by engineer in charge. 34 m&l for glazedcoloured ceramic tiles in vertical surface 300x 600x 7 mm / 300x 450x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick rendering in cement mortar 1:4 complete all as specifiedand directed. 35 s&f in repairs sinks made of stainless steel 1.0 mmthickkitchenorlaboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by engr in charge. 36 m&l for repair to broken sides / bottom of roof projection , facia by all means i.e. either by cement plaster of any thickness or by cement concrete 1:1.5:3 ( nominal mix ) type a 0, using 12.5 mm graded stone aggregate etc, using chicken wire mesh to reinforce & form work as required with two coats of appex paint over primer complete all as specified and as directed by the engineer in charge. 37 m&l for preparation of old decorated surfaces of walls including washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of oil bound distemper ( white / tinted ) on walls complete all as specified and as directed by the engineer in charge. 38 m&l for preparation of old decorative surfaces including scraping down smoke dust mould, mass and efflorescent, salt and trading oils and greasy spot etc. on ceiling including cornices, plasters etc. ( plastered or unplastered surfaces ) and applying one coat of white ( lime ) wash on old washed surfaces all as specified complete. 39 taking down cement or cement lime plaster of any description on brick or stone walls etc including ranking out joints hacking for key scrubbing down with water etc complete all as specified and as directed by the engineer in charge 40 m&l for rendering 15mm thick on fair faces of brick work / stone work or concrete surfaces ( cement plaster 1:6 ) finished even and smooth without using extra cement complete all as specified and as directed by the engineer in charge 41 m&l for rendering 5mm thick cement mortar ( 1:3 ) as in ceiling, soffit of staircase, chhajjas facia etc including cement slurry etc complete all as specified and as directed by the engineer in charge. 42 m&l for oil bound distemper two coats over a coat of primer including preparation of newly plstered surfaces of walls or unplastered surfaces of walls complete all as specified and as directed by the engineer in charge. 43 m&l for three coats of white wash on ceilingsoffit of staircase, chhajjas facia etc newly plastered surfaces including preparation of newly plastered surfaces or unplastered surfaces complete all as specified and as directed by the engineer in charge. 44 m&l for preparation of old painted wooden surface of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint. complete all as specified and as directed by the engineer in charge. 45 m&l for one coat of synthetic enamel paint including preparation of old decorated steel surfacesof any description over 10 cm width or girth not otherwise described. complete all as specified and as directed by the engineer in charge. 46 taking down or up steel water tubing and connections including cleaning for re fixing / credit of 15 mm borecomplete all as specified and directed by engineer in charge. 47 all as per above item no 46 but 20 mm bore. 48 s & f steel water tubing, galvanised, medium grade, isi marked with all fittings andfixed on walls and ceilingsor laid in floors bore of pipe 15 mm complete all as specified and directed by engineer in charge. 49 all as per item no 48 above but 20 mm bore. 50 s&f in repair to rotational moulded vertical water storage tanks triple layer ( white colour ) with closed tops ( cylindrical ) hoisted and fixed in position 500 litre capacity including disconnecting and refixing the existing gi fitting and pipe complete all as specified and directed by engineer in charge. 51 s&f in repair to rotational moulded vertical water storage tankstriple layer ( white colour ) with closed tops ( cylindrical ) hoisted and fixed in position 1000 litre capacity including disconnecting and refixing the existing gi fitting and pipe complete all as specified and directed by engineer in charge. 52 s&f in repair ball valves high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed suitable for iron pipe 20mm bore having weight not less than 210 gms complete all as specified and directed by engineer in charge. 53 s&f in repairs hdpe pvc lid ( cover ) for 500 / 1000 litres capacitypvc tank complete all as specified and directed by engineer in charge. 54 s&f in repair gate valves gun metal with iron wheel head screwed both ends for iron pipe and fixed 20mm bore fixed complete all as specified and directed by engineer in charge. 55 s&f in repair bib taps long body , cast copper alloy, fancy type with crutch or butterfly handles, chromium plated, screwed down to iron pipes or for brass ferrule of 15 mm borecomplete all as specified and directed by engineer in charge. 56 s&f in repair stop valves, cast copper alloy, fancy type, chromium plated with long shank & cup ( concealedtype ) with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm bore complete all as specified and directed by engineer in charge. 57 s&f in repair stop valves, cast copper alloy, fancy type, chromium plated with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm bore complete all as specified and directed by engineer in charge. 58 s&f in repair two way stop valves, cast copper alloy, fancy type, chromium plated with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm borecomplete all as specified and directed by engineer in charge. 59 s&fin repair 15 mm pillar taps swan neck cast copper alloy, with capstan heads, chromium plated screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nutsscrewed for iron pipes and fixed , fancy typecomplete all as specified and directed by engineer in charge. 60 s&f in repair brass chromium plated waste coupling 32mm bore whb complete all as specified and as directed by engineer in charge. 61 s&f in repair 15mm dia pvc connection 450 mm long with brass nuts complete all as specified and as directed by engineer in charge. 62 s&f in repair 10 litre pvc valve less symphonic action type low levelflushing cistern with inlet ball valve float and handle incl cibracketand 32mm bore pvc flush pipe and connection to pipe complete all as specified and as directed by engineer in charge. 63 s&f in repair cp towel rail 450mm long 20mm dia fixed with and including chromium platedbrass screws and wooden / plastic cleatscomplete all as specified and as directed by engineer in charge. 64 s&f in repair glass shelf assembly consisting of 5.5 mm thick sheets glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed by engineer in charge. 65 s & fin repair corner glass shelf with bracketof make bea 46 of prayag or equivelent in marco / zim complete all as specified and directed. 66 s&f in repairs vitreous china wash down water closet pan ( pedestal pattern ) excluding flushing cistern and flush pipe and including p or s trapcomplete all as specified and as directed by engineer in charge. 67 s&f in reapir vitreous china squatting pan “orrisa” pattern of size 580mmx440mm “white” with integral foot rest ( excluding flushing cistern and flush pipe ) incl provision of cement concrete bedding, ci ‘p’ trap 100mm dia connection to trap and flushing pipe, anti syphonage complete all as specified and directed by engineer in charge. 68 s&f in repairscp bottle trap with internal partition 32mm size 300 mm x 190 mm with wall connection pipe and wall flange complete all as specified and as directed by engineer in charge. 69 s&f in repairs 32mm bore and 75cm long pvc flexible waste pipe for whb complete all as specified and as directed by engineer in charge. 70 s&fin repair 900mm x 600mm x 5mm thick fancy type designer fancy looking mirror of selected quality glass, mounted on 12mm thick board base and sealed the edges with pvc taping and fixed to pvc plug with chromium plated brass screws and cup washers complete all as specified and as directed by engineer in charge. 71 s&f in repairs vitreous china wash hand basin of size 550 mm x 400 mm white, flat back incl angle iron bracketsincl waste pipe of 32 mm dia of suitable length, pvc connection of 15 mm dia & 450 mm long with ptmt nuts with 32 mm dia brass chromium plated bottle trap and waste coupling complete all as specified and as directed by engineer in charge. 72 s&f in repairplastic water closet seat cover white closed pattern with flat bottom and cover incl mild steel chromium plated hinging device complete all as specified and as directed by engineer in charge. 73 s&f in repair hand shower ( health faucet ) with 1 meter long easy flex tube in chrome finish & wall hookcomplete all as specified and as directed by engineer in charge. 74 s&f in repairs mild steel chromium plated grating ( round ) 125 / 150mm dia fixed over floor / nahani trap ( with hole and without hole ) complete all as specified and as directed by engineer in charge. 75 s& finrepair110 mmborepvc ( swr ) pipesinglesocketedinany lengthwithrubber ringjoints, laidintrenchesorinfloorsetcincludingremovingfromsite completeallasspecifiedanddirectedbyengr in charge. 76 s&f in repair pvc ( swr ) bends any radius for 110 mm bore pvc pipe with cement joints complete all as specified and as directed. 77 s& finrepair75 mmborepvc ( swr ) pipesinglesocketedinany lengthwithrubber ringjoints, laidintrenchesorinfloorsetcincludingremovingfromsite completeallasspecifiedanddirectedbyengr in charge. 78 s&f in repair pvc ( swr ) bends any radius for 75 mm bore pvc pipe with cement joints complete all as specified and as directed. 79 supply and fixing in repair door seal, length varied from 750 mm to 900 mm complete all as specified&directedby engineer in charge . 80 s&fin repair of150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specifiedand directed. 81 s&f in repair 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specifiedand directed. 82 s&f in repair mild steel helical door spring 300 mm ordinary rat tail type incl roller and roller plate complete fixed with screws to wooden frame or with welding to steel frames complete all as specifiedand directed by engr in charge. 83 s&f drappery curtain rods decorative type stainless steel 304 grade, 25mm nominal diaand having wall thickness 1.40 mm of approved quality / make including fixing oftwo number decorative brackets fixed in brick / concrete wall, two number knob on both ends of curtain rods ( the length of each curtain rod will be 1.00m to 2.50m long ) complete all as directed and specified. 84 s&f in repair 100 mm long butt hinges medium weight cold rolled mild steel alloy with galvanized complete all as specifiedand directed. 85 s&f in repair aluminium frame powder coated any colour ( minimum thickness of powder coating 50 micron ) for doors, windows, partiations, ventilators with one or more rebates including joining cleat for fixing etc. ( without taking off shutters from the frames ) complete all as specified 86 m / lfor powder coatedaluminium door shutters, aluminium section weighing 1.3 kg / m approx including each shutter having 2 nos. ‘d’ type aluminium handles of 200 mm long, 2 nos. aluminium tower bolts of 200 mm long and 1 no. mortice lock of 6 lever with key in duplicate, regulated by double action hydraulic floor door spring, shutter partly glazed with 5.5 mm thick sheet glass and partly panelled with 12 mm thick pre laminated particle board fixed with glazing clips, rubber beadings and aluminium beading complete all as specifiedand directed. note: ( glass & prelaminated particle board paid separately ) 87 supply and fix sheet glass 5.5 mm thick of selected quality ( tinted glass ) exc. 0.5 sqm each fixed to aluminium frame work with necessary rubber beading complete all as specified and directed by engineer in charge, . 88 demolition of cement concrete in sunken portion in any position not otherwise specifically provided for complete all as specifiedand directed by engr in charge. 89 m & l for 25 mm thick pcc1:2:4 type b0 ( 12.5mm graded aggregate ) as in sub base for floor complete all as specifiedand directed by engr in charge. 90 m&l for providing and laying 20mm thick cement mortar plaster for the protection of the treatment in 1:3 mixed with dr fixit pidiproof lw+complete all as specified and directed by engineer in charge, . 91 m & l for providing and making fillet of 75mmx75mm in size with cement concrete in 1:2:4 in sunken portion, complete all as specified and directed by engr in charge. 92 m&l for providing and applying two component based treatment having dgt of 1mm in two coats making an excellent impermeable coating by the name dr fixit pidifin 2k. surface to be prepared by cleaning with wire brush, removing all loose aggregate complete all as specified and directed by engineer in charge. 93 m&l for refilling lime concrete with brick aggregate ( course ) in lime mortar1:3, 300mm thick in the sunken with the help of proper tools & equipments & plants complete all as specified and directed by engr in charge. 94 m&l for providing and making cement concrete in 40mm thickness in 1:2:4 type b0 ( 12.5mm graded aggregate ) mixing dr fixit pidiproof lw+. complete in sunken upto the below level of tiling complete all as specified and directed by engr in charge. 95 m&l for providing and applying two coats making an excellent impermeable coating by the name dr fixit pidicrete urp. surface to be prepared by cleaning with wire brush removing all loose aggregate complete all as specified and directed by engr in charge. 96 m & l for cleaning and removing all scales and dirt, etc, from water tanks and from mouths of circulating pipes, etc ( capacity of tank exc 250 ltrs & n exc 500 ltrs ) and writing date of cleaning on water tank. complete all as specified and directed by engr in charge. 97 s & fin repairptmtlong body bib tap 15mm dia pipe with crutch or butter fly handle screwed down, screwed for iron pipe and fixed complete all as specified and directed by engr in charge. 98 s&f in repair pvc ( swr ) gully trap 125 / 110 mm setting and jointing with solvent 99 s&f in repair pvc ( swr ) floor trap 75mm with grating includingjointing with solvent 100 supply and fixing in repairs aluminium die cast door closer hydraulically regulated, designation no. 2, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 36 to 60 kg complete all as specifiedand directed. 101 s&f light shade vitrified tiles9 to 10 mm thick ( square / rectangular ) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed inneat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedincm 1:6 complete all as specified and directed.. 102 all as per item no 101 above but in vertical surfaces such as dado / skirting over and includingrendering 15 mm thick in cement mortar 1:4 complete all as specified and directed. 103 dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed. 104 m&l machine cut pre polishedkota stone slab flooring 20 25 mm thick over cement screed base 15 mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. 105 all as per item no 104above but in vertical surfaces such as dado / skirting over and includingrendering 15 mm thick in cement mortar 1:4 complete all as specified and directed. 106 m&l 75mm thick pcc 1:3:6, type c 2 using 40mmgraded stone aggregate as in plinth protection finished even & fair including making groove not exc 3.00 meter interval and filling the same with mixture of sand and bitumencomplete all as specified and directed. 107 m&l cement concrete 40mm thick type b 1, 1:2:4 ( using 20mm graded stone aggregate ) in floors pavings etc finished even & smooth with out using extra cement. 108 s&f glass dividing strips 3mm thick and 38mm wide inserted in position. 109 demolition of brick work or stone masonry including pillars, cornices, arches etc built incement mortar or cement lime mortar complete all as specified and dircted, 110 m&l brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4. complete all as specified and dircted, 111 m&l brick work with fly ash bricks, straight or curved on plan exc 6m mean radius in cm 1:4 complete all as specified and directed. 112 m&l cement plaster 15mm thick incm 1:4 on brick or concrete surfaces on external surfaces finished even and fair complete all as specified and directed.. 113 m&l applying three coats of white washon wallincluding preparation of newly plastered surfaces of wall complete all as specified and directed. 114 m&l applying two coats of super quality weatther proof exterior emulsion paint over & incl one coat of primer from the same manufacturer onexternal wall surfaces including preparation of new plastered surfaces on walls complete all as specified and directed, 115 m&l for non skid ceramic colouredtiles 7 to 8 mm thick ( square / rectangular ) area of each tiles exc 0.18 sqm but n. exc 0.38 sqm, in floors or dado etc set and jointed in neat cement slurry and pointed in coloured cement to match over 15 mm thick screed bed or bedding layer in cm ( 1:4 ) complete all as specified and directed. 116 all as per item no 115 above but in vertical surfaces such as dado / skirting over and includingrendering 15 mm thick in cement mortar 1:4 complete all as specified and directed....

Delhi Development Authority - Delhi

38801430 development of sports complex sector 23 ( now sector 33 ) rohini, dda.sub head : supplying, installation, testing and commissioning of electric sub station equipment’s including feeder pillars etc at sector 33, rohini. 1 sub head i ht panel & transformers and bus trunkingsupplying, installation, testing & commissioning of indoor type floor mounted metal clad, 11 kv vcb panel totally enclosed & fully interlocked, horizontal drawout, horizontal / vertical isolation floor rolling type breaker as per is 13118, iec 62271 100 & 62271 200 & 60694, as amended up to date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, elecrically charged and auto / manually closing breaker suitable for use on 11 kv, 3 phase, 50 hz a.c. supply with short circuit fault level of 350 mva, rated short circuit breaking capacity of 26.3 ka for 3 sec and internal arc fault withstand capacity of 26.3 ka for min. 1 sec complete with self contained, fully interlocked, rack in and rack out mechanism, air insulated but encapsulated copper bus bars of 800 amps capacity, breaker featured with mechanical on / off indicator with hand trip device, spring release coil, shunt trip coil and auxiliary switch of 4 no+4 nc and equipped with following switchgears and accessories i / c connections suitable for 3 core x 240 sq. mm. xlpe 11 kv cable ( cable entry from rear bottom ) end termination with heat shrinkable jointing material etc. as required. note : ( i ) the panel board shall be oem made only. franchise made mv switchboards shall not be accepted. ( ii ) cost of end termination not included in this item. ( iii ) panel shall be type tested fromnablaccredited labs like cpri / erda etc. i / c seismic compliance zone iv and should be internal are tested aflr ( front, lateral, rear ) protections as per iec62271 200. 2 incomer switchgear panel 1 no. 800 amp. vcb, 500 mva, 26.3 ka / 3 sec. spring charged motor 230 v ac 1 no. – withdrawal type 11 kv / 110 volts three phase pt of class 0.5 accuracy for metering, class 5p10 for protection.and 100 va burden with associated encapsulated hrc fuses for primary isolation, space heaterwith 1 no. caliberated intelligent multifunction digital panel meter of 0.5 accuracy with multiline display with communication interface port rs485 for giving output on becnet / modbus protocol of ibms for recording v, a, kva, kvar, kw, kwhr, pf etc. complete with wiring connections etc. asrequired at site. 1 no. – ( 0 300 a ) ammeter, digital type withselector switch. 1 no. – microprocessor based numerical relay with o / l, e / f and s / c protection. 1 no. – set of dual core dual ratio 3 cts 150 / 75 / 5 / 5 a of 15 va burden and accuracy class – 1.0 for metering and class 5p10 for protection. trip circuit supervision relay. control switch indication lamps for on, off, tch, auto trip, r, y, b indication, spring charging space heater digital multi function meter , 96 x 96 mm with operation on modbus / tcp ip protocol emergency push button 1 set of surge arrestors as per oem recommendation earth switch with making capacity for cable side earthingoutgoing switchgear panel 2 nos. 800 amp. vcb, 500 mva, 26.3 ka / 3 sec.spring charged motor 230 v ac 2 nos. – ( 0 100 a ) ammeter, digital type with selector switch. 2 nos. – microprocessor based numerical relays with o / l, e / f & s / c protections. 2 sets – set of dual core dual ratio 3 cts 60 / 30 / 5 / 5 a of 15 va burden and accuracy class – 1.0 for metering and class 5p10 for protection.trip circuit supervision relay. control switch indication lamps for on, off, tch, auto trip, r, y, b indication, spring charging, push buttons, space heater with thermostatcomplete with all standard accessories for each outgoing as required at site. hooter digital multi function meter , 96 x 96 mm with operation on modbus / tcp ip protocol emergency push button 1 set of surge arrestors as per oem recommendation earth switch with making capacity for cable side earthingauxillary relays for protection of chilers.8 way alarm annunciator window.power pack with 220 volt ac input & 24 volt dc continuous output suitable for closing / tripping / indication of ht panel board with 2 nos. 12 volts each maintenance free batteries of 100 ah each for all 3 panels ( 1 i / c +2 o / g ) , charging unit, capacitor bank for emergency delivering for trip system complete with suitable capacity of ammeter & voltmeter i / c connections with 2.5 sq. mm frls insulated copper conductor cable etc. as required.all necessary items required for completion of panel like mcbs, dbs etc. shall be provided alongwith the panel.etc complete as required. 3 supply, installation, testing & commisioningof copper wound 1000 kva, 11 / 0.433 kv , delta / star, vector group dyn11, indoor mounting, oil cooled onan transformer with onload tap changers ( oltc ) having avs relay and rtcc for automatic sensing of incoming voltage, automatic operation of oltc and facility for remote manual operation of oltc, suitable for incoming voltage variation of +5% to 15% in equal steps of 1.25 % to give a constant secondary voltage. the transformer shall be provided with fittings, accessories, protection, first filing of oil etc. including buchholz relay oil / winding temperature, alarm / trip protection, surge arrestor, bidirectional rollers, wiring up to marshalling box, complete as per specifications and as required. the transformer shall be provided with arrangement of weather proof ht cable box to terminate 3cx240 sqmm xlpe cable onprimary and suitable capacity of bus trunking on secondry side with 8 mm thick gland plate on primary an secondary side. the transformers shall confirm to is: 1180 part vi & is 2026. the lossesshall be as per ecbc 2017 as amended from time to time. the transformer shall be suitable for solar power integration for net metering system. 4 supplying, installing by suspension on ceiling, testing and commissioning of following capacity sandwich type rising mains for use on 3 phase 4 wire 415 volts, 50hz a.c. supply with metal clad enclosure having ip 54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 nos aluminium bus bars having current density of 130 a / sq cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 nos aluminium strip of suitable size ( one on each side ) including, g.i. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required a ) 1600 a 50ka sc for 1 sec 5 sub head ii ht cable 6 supply of following sizes of 11kv grade multicore aluminium conductor xlpe armoured power cable as per is: 7098amended upto date as per the following size.3c x 240 sq mm 7 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 11 kv grade of following size in the existing rcc / hume / metal pipe as required.above 120 sq. mm and upto 400 sq. mm 8 supplying and making indoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core, xlpe aluminium conductor cable of 11kv grade as required : 240 sq mm 9 supplying and fixing cable route marker with 10 cm x 10 cm x 5mm thick g.i. plate with inscription there on, bolted / welded to 35 mm x 35 mm x 6 mm angle iron, 60 cm long and fixing the same in ground as required. 10 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 11 kv grade of following size in the existing masonry open duct as required.above 120 sq. mm and upto 400 sq. mm 11 sub head iii lt panel and apfc panel 12 main lt panel supply, installation, testing & commissioning of dust damp and vermin proof factory built modular bolted construction extendable type plc based auto synchronising, auto load transfer, auto load sharing, auto load balancing main lt panel suitable for 415 v, 3 phase, 4 wire 50 hz. ac supply system fabricated in compartmentalized design from crca sheet steel of 2mm thick for frame work and covers, doors of1.6 mm thick sheet & 3mm thick for glands plates having 4b segregation and ip 42 protection i / c cleaning and finishing complete with 9 tank process for powder coating of approved shade &color, short circuit withstand capacity of 31 mva for 1 sec. bottom base channel of ms section not less than 75mm x 50mm x 5mm thick, fabrication shall be done in transportable sections, entire panel shall have a common aluminum earth bar of size 50mm x 6mm at the rear with 2 nos. earth stud, solid connections from main bus bar to switch gears with required size of al. bus bars and control wiring with 2.5 sq mm. frls pvc insulated copper conductor s / c cable, cable alleys, cable gland plates in two half having knock outs for cable glands of required size. panels shall be suitable for 415v, 3 phase, 4 wire, 50hz supply system and with 20% spare space, lifting hooks shall also be provided in case of large panels. ( panel shall be as per is / iec 61439 ( part 1 & 2 ) type tested from nablaccredited labs like cpri / erda etc. i / c. seismic compliance zone iv and should be internal arc tested at 50ka for 0.1 0.5 sec. as per iec 61641. panel should also have minimum mechanical impact strength of ik09 as per iec 62262 ) all acbs should have ics=icu=icw for 1 secall mccbs shall be rating for 50ka ( ics=icu ) . all mccbs above 63a should be provided with copper spreader terminalsapproval shall be taken for each panel before fabrication. galvanized hardwares with zinc passivation shall be used in fabrication of panels. panel vendor shall coordinate with the main electrical contractor .surge suppressor of 36 ka shall be provided between phase to neutral and neutral to earth at each bus section.all mccbs will have adjustable microprocessor o / l, s / c & inbuilt e / f protections.all outgoings shall be rating for 50ka ( ics=icu for 1 sec ) set of ryb phase indicating lamps with control mcbs on each outgoing to be provided. each backed up with 2a mcb.acb outgoing shall be provided with trip lamp also. all multifunction meters are suitable ( transformer shall be provided with suitable ratio cl 1, 15va cast resin cts.all outgoings shall be provided with multifunction meters of 3 phase, with all functions with rs 485 communication port. cable entry suitable from top and bottomdlp gas flooding system using heat detection tube for complete lt panel including gas, gasbank, tubes , lp switch, master control unit, associated piping network, actuators, valves etc complete as required.interlocking between transformer and bus couplers feeders shall be provided to avoid paralleling power supply of discom.details incoming from transformers ( 2 nos. 1000kva ) incomer feeder 2 nos.a ) 1600 a, 4p, 50 ka air circuit breaker horizontal drawout typeof fault breaking capacity 50ka ( ics=lcu =icw for 1 sec ) upto 690v ) electrical draw out motorized operated, fitted with interlocked door, automatic safety shutters, mechanical on / off and service / test / isolated position indicators and frame earthing contact, conforming to is 13947 2 1993 as amended up to date complete with following accessories for each acb 2 nos. b ) independent electrical / manualspringclosing mechanism i no. c ) microprocessorrelease ( emi& emc certified ) for over current, earth fault & short circuit protection i set. d ) calibrated intelligent multifunction digital panel meters of class 0.5s accuracy with communication interface port rs 485 for recording voltage ( between phases and between each phase and neutral ) , current ( in each phase and neutral ) , kva, kw, kwhr, kvar, pf, 64 samples / cycle, total harmonic distortion, with suitable rating ctsetc. complete with wiring , connections etc. 3 nos. phase indication led lamps with 2 amp back up mcb, breaker on / off indicating light with 2a mcb, test terminal block set, circuits as per standard practice, auxiliary contacts for positive interlocking of the breakers as required. shunt trip coil 220v a.c. 27 undervoltage with definite time relay 1 no1 no. dc under voltage trip relayincoming breaker ( from dg 750 kva ) a ) 800 a, 4p, 50 ka air circuit breaker horizontal drawout typeof fault breaking capacity 50 ka ( ics=lcu =icw for 1 sec ) upto 690v ) electrical draw out motorized operated, fitted with interlocked door, automatic safety shutters, mechanical on / off and service / test / isolated position indicators and frame earthing contact, conforming to is 13947 2 1993 as amended up to date complete with following accessories for each acb 1 nob ) independent electrical / manualspringclosing mechanism i no. c ) microprocessorrelease ( emi& emc certified ) for over current, earth fault & short circuit protection i set. d ) calibrated intelligent multifunction digital panel meters of class 0.5s accuracy with communication interface port rs 485 for recording voltage ( between phases and between each phase and neutral ) , current ( in each phase and neutral ) , kva, kw, kwhr, kvar, pf, 64 samples / cycle, total harmonic distortion, with suitable rating ctsetc. complete with wiring , connections etc. 3 nos. phase indication led lamps with 2amp back up mcb, breaker on / off indicating light with 2a mcb, test terminal block set, circuits as per standard practice, auxiliary contacts for positive interlocking of the breakers as required. shunt trip coil 220v a.c. 27 undervoltage with definite time relay 1 no1 no. dc under voltage trip relayrpr reverse power relay 1 nobus coupler 1600 amp 4 pole acb 1 set.a ) air circuit breaker horizontal drawout typeof fault breaking capacity 36ka ( ics=lcu =icw ) upto 433v ) electrical draw out motorised operated, fitted with interlocked door, automatic safety shutters, mechanical on / off and service / test / isolated position indicators and frame earthing contact, conforming to is 13947 2 1993 as amended up to date complete with following accessories for each acb1 no. b ) independent electrical / manualspringclosing mechanism i no. c ) 3 nos. phase indication led lamps with 2 amp back up mcb, breaker on / off indicating light with 2a mcb, test terminal block set, circuits as per standard practice, auxiliary contacts for positive interlocking of the breakers as required. bus coupler shall have equipped with the following:shunt trip coil 220v a.c. breaker control switch 16a ( mcb 10 ka ) bus bar1500 amps capacity tpn aluminium extensible type main bus bars of minimum of ( as per capacity of corresponding incoming / bus couplers ) , and auxiliary bus bar of suitable capacity with heat shrinkable coloured sleeves and i / c dmc / smc bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 35 mva for 1 sec. ( n=50% ) outgoings: all microprocessor based release acb / mccb of following capacity and rating, 36 ka ( ics=icu= 100% upto 690 v ) with 3 phase 4 wire dual source type multifunction meter of class 0.5s accuracywith communication interface port rs 485 for recording v v ( between phases and between each phase and neutral ) , current ( in each phase and neutral ) , kva, kw, kwhr, kvar, pf, 64 samples / cycle, total harmonic distortion, with suitable rating cts etc. complete with wiring , connections etc. 630 a 36 ka, tp mccb 2 nos. ( for cap. panel ) 800 a 36 ka, 4p acb 2 nos. ( 1 for electric room near main building + 1 no. spare ) 400 a 36 ka, 4p mccb 3 nos. ( 1no. for fire fighting panel + 1no. for football feeder pillar+1 no. spare ) all thermal magnetic based release mccb of following capacity and rating, 36 ka ( ics=icu= 100% upto 690 v ) with 3 phase 4 wire dual source type multifunction meter of class 0.5s accuracywith communication interface port rs 485 for recording v v ( between phases and between each phase and neutral ) , current ( in each phase and neutral ) , kva, kw, kwhr, kvar, pf, 64 samples / cycle, total harmonic distortion, with suitable rating ctsetc. complete with wiring , connections etc. 200 a 36 ka, 4p mccb 3 nos. ( 2 nos. for hockey fields ) 160 a 36 ka 4p mccb 5 nos. ( 1 no. for stp + 4 nos. spare ) 100 a 36 ka 4p mccb 4 nos. ( 1 no. water supply pumps + spare 3 nos ) interlocking:electrical interlocking through advance contacts / contactorsin mccb / acbs ( incomers & bus couplers ) should be provided to ensure that only one supply is available at a time on each section of bus and to eliminate any possibility of accidentally approaching two supplies at one bus section as per single line diagram enclosed.hmi 1 setnecessary interlocking with plc auto controls such that 2 nos. t / f incomer, 1 no bus cupler, 1 nos dg incomer, shall be successfully operational in all possible combinations. 13 apfc panel 215 kvar ( hybrid type ) a ) supplying, installation, testing & commissioning of factory built floor mounted auto manual power factor correction system panel of 215 kvar capacity having 3 phase, mixed die electric ( total power loss not exceeding 0.50 w / kvar ) power capacitor in 8 steps, filled with suitable oil and provided with 25 kvar fixed capacity and balance electronic thyristor switching & with 7.0% detuned filters to suppress switching of inrush current and reducing harmonics to improve capacitor life.b ) the system shall have microprocessor based power factor controller with power conditioner savers using rapid instruction semi conductor micro controller provided in the command module for target p.f. setting with digital p.f. display. the controller consists: var / fifo / binary mode, all three powers, i.e. kva, kw and kvar phase wise and system harmonic in all three phases. all three voltages, phase to phase to neutral, supports modbus rtu protocol with rs 485 port with communication card which can communicate with existing bms system on bacnet / modbus protocol. the controller graphical lcd display window shall be as per manufacturer’s standard and good engineering practice with programmable back light on time.c ) the system shall be provided with required capacity master relay acb, to check its main operating parameters such as over loads, short circuit, etc.d ) the panel shall be fabricated in compartmentalized design from crca sheet steel of 2mm thick for frame work and 1.6 mm thick for covers, i / c cleaning & surface treatmentwith 7 tank process before powder coating in approved shade, having 800 amp capacity extensible type tpn aluminium alloy bus bars of high conductivity, dmc / smc bus bar supports, with short circuit withstand capacity of 31 mv a for i sec., bottom base channel of ms section not less than 100mm x 50mm x 5mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 32mmx5mm at the rear with 2 nos. earth stud, solid connections from main bus bar to switch gears / accessorieswith required size of al. bus bars and control wiring with 2.5 sq.mm. pvc insulated frls copper conductor single core cable, of2 mm thick ms sheet, provided with exhaust fans ( with thermostat ) and grills for proper ventilation, interconnections with suitable size conductor cables & lugs and accommodating the following switchgears & accessories:incomer:1 no. 630 amps four pole, 36 ka ( icu=ics ) , mccbwith microprocessor based release with o / c, s / c protection release all indication, front operating handle & door interlock3 nos. phase indication led lamps with 2amp back up mcb, breaker on / off indicating light with 2a mcb, test terminal block set, circuits as per standard practice, auxiliary contacts for positive interlocking of the breakers as required. automatic p.f.c.r. 11 stage with power factor meter & cts for unbalanced load 1 set.bus bar :tp aluminium extensible type main bus bars of minimum of 800 amps. capacity & auxiliary bus bars of suitable capacity with heat shrinkable coloured sleeves and i / c dmc / smc bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 35ka capacity.outgoings : control mcb / mccbs with capacitor banks:125amp. tp mccb 35ka thermal magnetic release having o / l & s / c protection with 50 kvar, 415 v heavy duty capacitor bank, capacitor duty contactoretc 2 sets.63amp. tp mccb 35ka thermal magnetic release having o / l & s / c protection with 25 kvar, 415 v heavy duty capacitor bank, capacitor duty contactoretc 3 sets.32amp. tp mcb 35ka thermal magnetic release having o / l & s / c protection with 10 kvar, 415 v heavy duty capacitor bank, capacitor duty contactoretc 3 sets.25amp. tp mcb 35ka thermal magnetic release having o / l & s / c protection with 5 kvar, 415 v heavy duty capacitor bank, capacitor duty contactoretc 2 sets.apfc panel as above 14 earthing 15 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as require 16 earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. 17 supplying and laying 25 mm x 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with nut, bolt, spring, washer etc. as required. ( jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm ) 18 providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required 19 providing and fixing 25 mm x 5 mm copper strip in 40 mm dia g.i. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re filling etc. as required. 20 supplying and laying 25 mm x 5 mm g.i strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with g.i. nut, bolt, spring, washer etc. as required. ( jointing shall be done by overlapping and with 2 sets of g.i. nut bolt & spring washer spaced at 50mm ) 21 providing and fixing 25 mm x 5 mm g.i. strip in 40 mm dia g.i. pipe from earth electrode including connection with g.i. nut, bolt, spring, washer excavation and re filling etc. as required 22 providing and fixing 25 mm x 5 mm g.i. strip on surface or in recess for connections etc. as required....

Municipal Corporation Of Delhi - Delhi

38564196 requirement of garden tools and machine in ward no. 164 ( dakshinpuri ) / sz. 1 development 2 garden rake ( datali ) types of garden rake forged spikematerial of handle of garden rake bamboonumber of spikes8the size of the rake measured from from the centre of extreme spike at one end to the centre of extreme spike at other end in mm ( with tolerance @ ± 5% ) 450the length of the handle of garden rake ( in metres ) 1.75 mdiameter of the handle of garden rake ( in mm ) 35 mmthe height or depth of the spikes ( in mm ) 50 3 spade ( phawra ) length of blade in mm tolerance of + 5mm allowed250mouth width of blade in mm tolerance of + 5mm140thickness of blade sheet in mm tolerance of + 5mm50length of shaft in mm ( tolerance + 25mm ) 700material of bladestainless steeltype of handled shaped handle 4 axe ( kulhadi ) 550 650 hv or 54 62 hrc when tested at a point approx 13 mm from cutting edge 5 pick axe ( gaiti ) material of axe blade as per is 1570 1961t 60material of handlewoodminimum overall length of blade in mm545minimum width of chisel edge in mm25minimum rise of point and chisel or tee in mm20nominal mass in kg3.5length of handle in mm1400 6 khurpimaterial of khurpi carbon steelmaterial of handle – timberthickness of blade in mm 6thickness of cutting edge of blade in mm 0.5 or 0.6size of khurpi blade ( lx w ) in mm x mm ( with ± 2 mm tolerance ) 200 x 80overall size of khurpi ( l x w x h ) in mm x mm x mm 30.1 x 13.8 x 6.8weight of khurpi in gram 200 7 secateurs ( katiya ) length200 millimeterweight 350gcutting edge length 45mmcutting edge length 50 mmblade material hardened & tempered high carbon steel blade with rust preventing coatingcutting capacity 15 millimeterspring leaf spring sytem 8 hedge sheerblade size 250 millimeterthickness of the blade, min4 millimeterover all length570 millimeterwidth of the blade 32 millimeterhandle material pvcblade material high carbon steel 9 lopper ( adjustable tree looper ) blade material high carbon steel with hard surface treatmentcutting dia 36 millimeterlength 750 millimeterweight 400ghandle material aluminium alloy 10 supply of petrol bush cutter by engine all standard accessories, attachment and having following specification : engine : not less than 43 cc ( 2 stroks ) cutting width : not less than 42 cmwidth : not more than 9 kgbody : steel / carbon steel one year warrantycarburetor ( wallbro ) 11 water sprinklermax engine bhp ( hp ) 400 horsepowergross vehicle weight ( gvw ) ( kg ) 21 kilogramturning radius ( mm ) 5 millimeterwater tank capacity ( litres ) 30000 liter 12 rose cane 13 bamboo broom with wooden handle and iron ring 14 telescopic tree pruner 15 supply ofhessian cloth, of size 54” width of good quality 16 supply of pvc pipe 1’ size of good quality...

Irrigation And Flood Control Department - Delhi

38481096 providing and fixing play equipment at dda park double storey in karol bagh assembly constituency 23 1 demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge.in cement mortar 2 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50metres lead. 3 taking out existing cc interlocking paver blocks from footpath / central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of engineer in charge. 4 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level :1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) : 8 graded stone aggregate 40 mm nominal size ) 5 12 mm cement plaster of mix : 1:4 ( 1 cement: 4 coarse sand ) 6 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. 7 providing thematic painting work on outer face of existing boundary wall by depicting theme of nature / culture by using exterior weather proof emulsion paint i / c design charges etc complete or as per direction of engineer in charge. 8 making bajri path including preparation of subgrade, supplying and laying brick aggregate of 50 mm nominal size 7.5 cm deep with blinding material consisting of 12 mm moorum and 12 mm red bajri consolidated with road roller. 9 brick edging laid lengthwise with half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres :with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 10 steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 11 providing and fixing stainless steel ( grade 304 ) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i / c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer incharge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. ) . 12 manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type iii of astm d 4956 01 as approved by engineer in charge, letters, borders etc. as per irc : 67 2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class ii of astm d 4956 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. the rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer in charge. ( structural frame work including m.s. plate to be provided separately. rectangular area of the sheet only shall be measured for payment ) . overhead informatory road signage 13 providing and fixing play equipments ( swings ) at sites as per specifications and direction of engineer in charge.duplex maps d01combination set 3 in 1frp wave slide 2.1 mtr.toddler swingstandard swingcircular swingsimply go roundhalf round netstd. see saw ( double ) kiddies benchspring rider jumboroad rash joy stationfun slider 05, ...

Department Of Defence - Delhi

38458069 bids are invited for carpenter tools and machines foot rule or steel tape , foot rule or steel tape , fooy rule or steel tape , steel measuring scale , marking knife , try square machinist steel square , premium aluminum alloy double side , bevel square wooden , carpenter marking gauge , carpenter mortise gauge , hand saw , tenon saw , metal jack plane , metal smoothing plane , firmer chisel , mortise chisel , screw driver , mallet medium size , claw hammer , oil stone carborundum universal silicon carbide combination rough and fine , hand brush for cleaning , construction scale ss , spring caliper inside , spring caliper outside , wing compass , trammel , sprit level , rip saw , cross cut saw , key hole saw , fret saw frame , compass saw , carpenter adze , trying plane metal , plane rivet adjustable , plough plane , spoke shaves , plane adjustable circular , router plane , moulding plane set , cabinet scraper , gauge chisel firmer 6 mm , gauge chisel firmer 10 mm , gauge chisel firmer 12 mm , gauge chisel firmer 16 mm , gauge chisel firmer 20 mm , gauge chisel scribing 6 mm , gauge chisel scribing 10 mm , gauge chisel scribing 12 mm , gauge chisel scribing 16 mm , gauge chisel scribing 20 mm , ball pein hammer 600 gms , cross pein hammer 600 gms , pincer 50 mm , file half round 2nd cut 250 mm , file half round wood rasp bastard250mm , file slim taper 100 mm , file slim tape 150 mm , card file steel wire brush for file 200 mm , hands drill double pinion steel drill chuck drive sizes 6 mm to 10 mm , country drill with bow ball bearing type 620 x 726 mm , ratchet brace 250 mm swap , hand auger 10 mm , hand auger 12 mm , hand auger 14 mm , hand auger 16 mm , hand auger 18 mm , hand auger 20 mm , hand auger 22 mm , hand auger 25 mm , centre bits 6 mm , centre bits 8 mm , centre bits 10 mm , centre bits 12 mm , expansion bit sets 218 x 171 mm , twist drill bits 6 mm , twist drill bits 8 mm , twist drill bits 10 mm , twist drill bits 2 mm , counter sink bit rose type 12 1 9310 mm , twist drill bits 2 mm , counter sink bit rose type 12 side cutting pliers 250 x 250 mm , plunger saw set or pistol grip type 300 x 300 mm , number punch 12 mm , slip stone 100 mm , round crow bar with chisel and claw end 1070 x 25mm , g clamp 100 mm , g clamp 150 mm , g clamp 250 mm , t bar cramp 0 6 meter , t bar cramp 1 25 meter , t bar cramp 1 75 meter , carpenter vice material cast iron item dimensions lxwxh 15 x 10 x 5 centimeters style heavy duty heavy duty cast iron material used , saw sharpening vice 250 jaws , carving tools set , glass cutter , nail punch , surface plate 600x 600 mm , carpenter s wooden work bench 2400x920x800 mm height smooth finishedpolished , grease gun , spanner double ended , portable circular saw machine , portable planning machine , power drill machine industrial type , portable sander machine electric , portable jig saw machine , portable router machine industrial type , power screw driver , combined surface and thickener , circular saw machine , lathe wood turning , tenoning machine single ended , mortising machine combine hollow chisel and chain , bench grinder 200 mm whole d e pedestal , drill machine , portable electric drill wolf type , drills chuck , portable disc sander , adjustable saw sharpener , electric heater 1000 or 1500 w 1 nos 102 electric blower portable , moisture meter , universal wood working machine , electrical drying oven , vertical bandsaw machine , cd and dvd of different joint related to carpenter works and variety design of modern furniture , providing and laying steel office almirah small , providing and laying glass door almirah , providing and laying steel table for class rooms , providing and laying steel table with cubboard officer , providing and laying automation table l type class i officer , providing and laying computer table , providing and laying chair with arms , providing and laying executive rev chair high back , providing and laying centre table , providing and laying sofa set 3 1 1 seater , vertical support for desk , providing and laying self contained drinking water cooler of 150 ltrs total quantity : 1485...

Irrigation And Flood Control Department - Delhi

38438193 providing and fixing play equipment at dda park double storey in karol bagh assembly constituency 23 1 demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge.in cement mortar 2 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50metres lead. 3 taking out existing cc interlocking paver blocks from footpath / central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of engineer in charge. 4 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level :1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) : 8 graded stone aggregate 40 mm nominal size ) 5 12 mm cement plaster of mix : 1:4 ( 1 cement: 4 coarse sand ) 6 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. 7 providing thematic painting work on outer face of existing boundary wall by depicting theme of nature / culture by using exterior weather proof emulsion paint i / c design charges etc complete or as per direction of engineer in charge. 8 making bajri path including preparation of subgrade, supplying and laying brick aggregate of 50 mm nominal size 7.5 cm deep with blinding material consisting of 12 mm moorum and 12 mm red bajri consolidated with road roller. 9 brick edging laid lengthwise with half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres :with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 10 steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 11 providing and fixing stainless steel ( grade 304 ) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature ( wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i / c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer incharge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. ) . 12 manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type iii of astm d 4956 01 as approved by engineer in charge, letters, borders etc. as per irc : 67 2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class ii of astm d 4956 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. the rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer in charge. ( structural frame work including m.s. plate to be provided separately. rectangular area of the sheet only shall be measured for payment ) . overhead informatory road signage 13 providing and fixing play equipments ( swings ) at sites as per specifications and direction of engineer in charge.duplex maps d01combination set 3 in 1frp wave slide 2.1 mtr.toddler swingstandard swingcircular swingsimply go roundhalf round netstd. see saw ( double ) kiddies benchspring rider jumboroad rash joy stationfun slider 05, ...

Public Works Department - Delhi

37930525 tender for up gradation / modification of substation equipment for cj 4, tihar jail, new delhi. 1 ht paneldismantling of the exixting ht panel and supplying, installation, testing & commissioning of indoor type floor mounted metal clad, 11kv vcb panel with 03no. vcbs, totally enclosed & fully interlocked, horizontal drawout, horizontal / vertical isolation type breaker as per is13118, as ammended up to date and additional specification, having capacities as mentioned below, single break, trip free mechanism, manually charged and auto / manually closing breaker suitable for use on 11kv, 3ph, 50hz ac supply with short circuit fault level of 350mva, complete with self contained, fully interlocked, rack in and rack out mechanism, air insulated but encapsulated copper bus bar of 630a capacity, breaker featured with mechanical on off indicator with hand trip device, spring release coil, shunt trip coil and auxillary switch of 4no+4nc and equipped with following switchgears and accessories i.e. connections with exixting xlpe 11kv cables ( cable entry from bottom / top / side ) end termination with heat shrinkable jointing material etc. as reqd. 2 a ) incoming 1 no 630 amp vcb 3 b ) 11 kv / 110 volts pt class 0.5 accuracy and 50 va burden with 1 no. voltmeter ( 0 15 kv ) , digital type selector switch for voltmeter and protection fuses / mcb for ht metering upto 11 kv on incomer. ( 0 50 100a ) comply with is 3156. pt must not be on the top of the panel. it must be floor rooled placed rear side of panel or on the cb trolley 1 set 4 c ) digital type multi function meterand digital type ammeter 1 no. 5 d ) flush mounted type microprocessor based numercial idmt relay with o / l, e / l and s / c 1 no. 6 e ) dual core / single core;separate sets, dual ratio 3 nos. cts 200 / 100 / 1 a of 5 va burden and accuracy class 0.5 for metering and class 5p10 for protection comply with is 2705 1 set 7 f ) r, y, b on, off, trip indication with control mcb 1 set 8 outgoing 9 a ) 630 amp vcb 2 nos 10 b ) digital type multi function meter 2 nos. 11 c ) flush mounted type microprocessor based numercial idmt relay with o / l, e / l and s / c 2 nos. 12 d ) ( 3 nos each ) of dual core dual ratio 3 cts 100 / 50 / 1 a of 5 va burden and accuracy class 0.5 for metering and class 5p10 for protection 2 set. 13 e ) annunciator 6 window 2 nos 14 f ) hooter 2 nos 15 g ) aux. relay 6 nos 16 h ) trip super vision relay 2 nos. 17 power panel pack with 220 volt ac input & 24 volt dc continuous output suitable for closing / tripping / indication of 4nos. ht panel boards with 2 nos. 12 volts each maintenance free batteries of 100ah each, charging unit for emergency delivering for trip system compete with suitable capacity of ammeter and voltmeter i / c connections with 2.5 sq. mm frls insulated copper conductor cable etc. as required. ( i / c credit of dismantled ht panel to the agency ) 18 main lt cum emergency paneldismantling the exixting lt panel and supplying, installation, testing & commissioning of cubical modular type lt panel suitable for 415 v, 3 phase, 4 wire 50 hz ac supply system fabricated in compartmentalized design having bus bar chamber duly fabricated from crca sheet steel of 2 mm thick for frame, back, sides, partition & doors and 3mm thick for glad plate duly powder coated in approved shade including cleaning & finishing complete with 7 tank process complete with2500 amp capacity extensible type four strip aluminium alloy bus bars of hight conductivity, dmc / smc bus bar supports having short circuit withstand capacity of 31 mva for 1 sec., bottom base channel of ms section not less than 100 mm x 50 mm x 5 mm thick, entire panel shall have a common earth bar of size 25 mm x 5 mm at the rear with 2 nos. earth stud, solid connections from main bus bar to switch gears with required size of al. bus bars, control wiring with2.5 sq. mm. pvc insulated copper conductor single core cable, cooling / ventilation fans including construction of suitable cc foundation, in & out connections and providing & fixing following switch gears therein i / c connections with existing cables etc. complete as required. ( i / c credit of dismantled lt panel to the agency ) 19 incoming trf 1 & 2 20 ( i ) 2 nos 2000 ampers four pole horizontal drawout type electrically operated air circuit breaker of fault breaking capacity 50 ka breaking capacity ( ics = icu = icw=100% ) for 1 second suitable upto 690v, fitted with interlocked door, automatic safety shutters, mechanical on / off and service / test / isolated position indicators and frame earthing contact, auxilary contacts, shunt trip, interlocking features etc. complete with self powered microprocessor based release for adjustable setting for over current, earth fault & short circuit protection with lcd display. pre overload and over temperature protection indication with individual fault indicating leds on release & all other standard features conforming to is 1397 2 : 1993 as amended up to date ( ii ) 2 sets ryb phase indication led lamps with 6a, 10ka, c curve back up mcb, breaker on / off / trip indicating light with 6a, 10ka, c curve backup mcb ( iii ) 2 nos. 3 phase intelligent multifunction digital meter to read v, a, kva, kwh, pf hz etc. with 3 nos. resin cast cts of 2000 / 5 a class 1.0 accuracy and 15 va burden and with 3 nos 6a, 10ka, c curve back up mcb. 21 incoming amf 1 & 2 22 ( i ) 2 nos 1000 ampers four pole horizontal drawout type electrically operated air circuit breaker of fault breaking capacity 50 ka breaking capacity ( ics = icu = icw=100% ) for 1 second suitable upto 690v, fitted with interlocked door, automatic safety shutters, mechanical on / off and service / test / isolated position indicators and frame earthing contact, auxilary contacts, shunt trip, interlocking features etc. complete with self powered microprocessor based release for adjustable setting for over current, earth fault & short circuit protection with lcd display. pre overload and over temperature protection indication with individual fault indicating leds on release & all other standard features conforming to is 1397 2 : 1993 as amended up to date ( ii ) 3 sets ryb phase indication led lamps with 6a, 10ka, c curve back up mcb, breaker on / off / trip indicating light with 6a, 10ka, c curve backup mcb ( iii ) 3 nos. 3 phase intelligent multifunction digital meter to read v, a, kva, kwh, pf hz etc. with 3 nos. resin cast cts of 1000 / 5 a class 1.0 accuracy and 15 va burden and with 3 nos 6a, 10ka, c curve back up mcb. 23 bus coupler 24 ( i ) 1 nos 2000 ampers four pole horizontal drawout type electrically operated air circuit breaker of fault breaking capacity 50 ka breaking capacity ( ics = icu = icw=100% ) for 1 second suitable upto 690v, withoutrelease, fitted with interlocked door, automatic safety shutters, mechanical on / off and service / test / isolated position indicators and frame earthing contact, auxilary contacts, shunt trip, interlocking features etc. ( ii ) 1 sets ryb phase indication led lamps with 6a, 10ka, c curve back up mcb, breaker on / off / trip indicating light with 6a, 10ka, c curve backup mcb 25 interlocking 26 ( i ) electrical interlocking through advance contacts in acbs ( all incomers & bus couplers ) along with mechanical interlocking 27 outgoing 28 ( i ) 1 no. 800 ampers four pole horizontal drawout type electrically operated air circuit breaker of fault breaking capacity 50 ka breaking capacity ( ics = icu = icw=100% ) for 1 second suitable upto 690v, fitted with interlocked door, automatic safety shutters, mechanical on / off and service / test / isolated position indicators and frame earthing contact, auxilary contacts, shunt trip, interlocking features etc. complete with self powered microprocessor based release for adjustable setting for over current, earth fault & short circuit protection with lcd display. pre overload and over temperature protection indication with individual fault indicating leds on release& all other standard features conforming to is 1397 2 : 1993 as amended up to date ( ii ) 1 sets ryb phase indication led lamps with 6a, 10ka, c curve back up mcb, breaker on / off / trip indicating light with 6a, 10ka, c curve backup mcb ( iii ) 1 no. 3 phase intelligent multifunction digital meter to read v, a, kva, kwh, pf hz etc. with 3 nos. resin cast cts of 800 / 5 a class 1.0 accuracy and 15 va burden and with 3 nos 6a, 10ka, c curve back up mcb. ( ii ) 4 sets 630a, fp, 36ka mccb ( ics=icu =100% ) withmicroprocessor based release with adjustable settinghaving o / l & s / c protection with rotary handle and spreader terminal. ( iii ) 4 sets on / offindicating light with 6a, 10ka, c curve backup mcb, auxiliary contacts with mcb. ( iv ) 6 sets 400a, fp, 36ka mccb ( ics=icu =100% ) withmicroprocessor based release with adjustable settinghaving o / l & s / c protection with rotary handle and spreader terminal. 29 ( v ) 6 sets on / offindicating light with 6a, 10ka, c curve backup mcb, auxiliary contacts with mcb. ( vi ) 15 sets 250a, fp, 36ka mccb ( ics=icu =100% ) withmicroprocessor based release with adjustable settinghaving o / l & s / c protection with rotary handle and spreader terminal. ( vii ) 15 sets on / offindicating light with 6a, 10ka, c curve backup mcb, auxiliary contacts with mcb. ( viii ) 5 sets 160a, fp, 36ka mccb ( ics=icu =100% ) withthermal magnetic based release with adjustable settinghaving o / l & s / c protection with rotary handle and spreader terminal. ( ix ) 5 sets on / offindicating light with 6a, 10ka, c curve backup mcb, auxiliary contacts with mcb. 30 apfc paneldismantling the exixting panel supply, installation, testing and commissioning of apfcpanel of cubical type compartmentalized and fabricated from 2 mmthickcrcasheethavingnecessarycable alleys, powdercoated, including connection and interconnection as required as per specificationscomplete with following accessories including supplying and fixing of 250kvarcapacitor. suitable for 415 volt, 3 phase, 4 wire, 50hzac, having630amps capacityextensible type tpnaluminumalloy busbarsofhighconductivitydmc / smcbus barsupports, withshort circuitwithstand capacityof31mvafor1sec., bottombase channel of ms section notlessthan 100mmx 50mmx5mmthick, fabrication shallbedone in transportable section, entire panel shall haveacommon earthbarofsuitable sizeattherearwith2nos.earthstud, solid connections from main bus bar to switch gears withrequired size of al. busbarsand control wiringwith2.5sqmmpvcinsulatedcopper conductor single core cable, cable alleys, cable glandplatesintwohalf, i / cprovidingand fixing following switch gears completeaspersite 31 a ) 630a fp 36ka mccb thermal magnetic release 1 nos. 32 b ) 12 stage apfcr relay 1 nos. 33 c ) louver with fan 2 nos. 34 d ) digital ammeter 1 nos. 35 e ) digital voltmeter & ammeter 1 nos. 36 f ) r, y, b, indication lamp 3 nos. 37 g ) 6a sp mcb 3 nos. 38 ( ii ) bus bars: 39 tpn aluminumbusbarsofminimum of630 acapacitywithheatshrinkablecolored sleeves and i / c dmc / smc bus bars supports at required intervals complete, for cross section, sizesupports&theirspacingetc.for withstandingfaultlevelof31mvafor1sec. 40 iii ) outgoings; 41 step details 50 kvar 2 nos. 42 1 ) 2 nos. 100a tp+n mccb 25ka with thermal magnetic release with adjustable setting for overload and short circuit protection withfollowingaccessories each capacitor bank 43 a ) 50kvarcapa.dutycontactor 2 nos. 44 b ) auto / off / manual switch 2 nos, 45 c ) on / off indicating lamp 2 set. 46 d ) 50kvar heavy duty capacitors 2 nos . 47 step details 25 kvar 4 nos. 48 1 ) 4 nos. 63a tp+n mccb 25ka with thermal magnetic release with adjustable setting for overload and short circuit protection withfollowingaccessories each capacitor bank 49 a ) 25kvarcapa.dutycontactor 4 nos. 50 b ) auto / off / manual switch 4 nos, 51 c ) on / off indicating lamp 4 set. 52 d ) 25kvar heavy duty capacitors 4 nos 53 step details 10 kvar 5 nos. 54 1 ) 5 nos. 40a tp+n mccb 25ka with thermal magnetic release with adjustable setting for overload and short circuit protection withfollowingaccessories each capacitor bank 55 a ) 10kvarcapa.dutycontactor 5 nos. 56 b ) auto / off / manual switch 5 nos, 57 c ) on / off indicating lamp 5 set. 58 d ) 10kvar heavy duty capacitors 5 nos 59 earthingearthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal / coke and salt as required. 60 providing and fixing 25 mm x 5 mm copper strip in 40 mm dia g.i. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re filling etc. as required. 61 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal / coke and salt as required. 62 providing and fixing 25 mm x 5 mm g.i. strip in 40 mm dia g.i. pipe from earth electrode including connection with g.i. nut, bolt, spring, washer excavation and re filling etc. as required. 63 providing and fixing 25 mm x 5 mm copper strip on surface orin recess for connections etc. as required. 64 providing and fixing 25 mm x 5 mm g.i. strip on surface or inrecess for connections etc. as required. 65 cablesupplying & fixingof following size xlpe insulated and pvc sheathed aluminium conductorarmoured power cable of 1.1 kv grade conf. to is 7098 ( part i ) in the existing trench complete etc as required. 66 3.5 x 400 sq.mm 67 3.5 x 300 sq.mm 68 3.5 x 185 sq.mm 69 3.5 x 120 sq.mm 70 supplying and making end termination with brass compression gland and aluminium lugs for following size of pvc insulated and pvc sheathed / xlpe aluminium conductor cable of 1.1 kv grade as required. 71 3½ x 400 sq. mm ( 82mm ) 72 3½ x 300 sq. mm ( 70 mm ) 73 3½ x 185 sq. mm ( 57mm ) 74 3½ x 120 sq. mm ( 45 mm ) 75 3½ x 95 sq. mm ( 45 mm ) 76 misc. civil workexcavation of the cable trenches in hard rock not exceeding1.5 meter in width, and lift upto 1.5 meter, including getting out the excavated soil and disposal of excavated soil as directed within a lead of 50 meter. 77 providing brick work ( in width 225 mm or more ) with f.p.s. bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand ) at all levels. 78 providing 15 mm thick cement plaster of mix 1:4 ( 1 cement : 4 fine sand ) at all levels....

Department Of Defence - Delhi

37721705 bids are invited for tools and machine for carpenter foot rule or steel tape , foot rule or steel tape , fooy rule or steel tape , steel measuring scale , marking knife , try square machinist steel square , premium aluminum alloy double side , bevel square wooden , carpenter marking gauge , carpenter mortise gauge , hand saw , tenon saw , metal jack plane , metal smoothing plane , firmer chisel , mortise chisel , screw driver , mallet medium size , claw hammer , oil stone carborundum universal silicon carbide combination rough and fine , hand brush for cleaning , construction scale ss , spring caliper inside , spring caliper outside , wing compass , trammel , sprit level , rip saw , cross cut saw , key hole saw , fret saw frame , compass saw , carpenter adze , trying plane metal , plane rivet adjustable , plough plane , spoke shaves , plane adjustable circular , router plane , moulding plane set , cabinet scraper , gauge chisel firmer 6 mm , gauge chisel firmer 10 mm , gauge chisel firmer 12 mm , gauge chisel firmer 16 mm , gauge chisel firmer 20 mm , gauge chisel scribing 6 mm , gauge chisel scribing 10 mm , gauge chisel scribing 12 mm , gauge chisel scribing 16 mm , gauge chisel scribing 20 mm , ball pein hammer 600 gms , cross pein hammer 600 gms , pincer 50 mm , file half round 2nd cut 250 mm , file half round wood rasp bastard250mm , file slim taper 100 mm , file slim tape 150 mm , card file steel wire brush for file 200 mm , hands drill double pinion steel drill chuck drive sizes 6 mm to 10 mm , country drill with bow ball bearing type 620 x 726 mm , ratchet brace 250 mm swap , hand auger 10 mm , hand auger 12 mm , hand auger 14 mm , hand auger 16 mm , hand auger 18 mm , hand auger 20 mm , hand auger 22 mm , hand auger 25 mm , centre bits 6 mm , centre bits 8 mm , centre bits 10 mm , centre bits 12 mm , expansion bit sets 218 x 171 mm , twist drill bits 6 mm , twist drill bits 8 mm , twist drill bits 10 mm , twist drill bits 2 mm , counter sink bit rose type 12 1 9910 mm , twist drill bits 2 mm , counter sink bit rose type 12 side cutting pliers 250 x 250 mm , plunger saw set or pistol grip type 300 x 300 mm , number punch 12 mm , slip stone 100 mm , round crow bar with chisel and claw end 1070 x 25mm , g clamp 100 mm , g clamp 150 mm , g clamp 250 mm , t bar cramp 0 6 meter , t bar cramp 1 25 meter , t bar cramp 1 75 meter , carpenter vice material cast iron item dimensions lxwxh 15 x 10 x 5 centimeters style heavy duty heavy duty cast iron material used , saw sharpening vice 250 jaws , carving tools set , glass cutter , nail punch , surface plate 600x 600 mm , carpenter s wooden work bench 2400x920x800 mm height smooth finishedpolished , grease gun , spanner double ended , portable circular saw machine , portable planning machine , power drill machine industrial type , portable sander machine electric , portable jig saw machine , portable router machine industrial type , power screw driver , combined surface and thickener , circular saw machine , lathe wood turning , tenoning machine single ended , mortising machine combine hollow chisel and chain , bench grinder 200 mm whole d e pedestal , drill machine , portable electric drill wolf type , drills chuck , portable disc sander , adjustable saw sharpener , electric heater 1000 or 1500 w 1 nos 102 electric blower portable , moisture meter , universal wood working machine , electrical drying oven , vertical bandsaw machine , cd and dvd of different joint related to carpenter works and variety design of modern furniture , providing and laying steel office almirah small , providing and laying glass door almirah , providing and laying steel table for class rooms , providing and laying steel table with cubboard officer , providing and laying automation table l type class i officer , providing and laying computer table , providing and laying chair with arms , providing and laying executive rev chair high back , providing and laying centre table , providing and laying sofa set 3 1 1 seater , vertical support for desk , providing and laying self contained drinking water cooler of 150 ltrs total quantity : 1485...

Department of Financial Services - Delhi

37641336 bids are invited for supply and installation of equipment total quantity : 2586 1 central management of multiple sound systems from a single processor 1 nos • sampling frequency rate internal 48khz / 44.1khz • signal delay 1.9 msec ( ad da @48khz ) • total harmonic distortion “0.05% ( +4dbu, gain: 6db, 48khz ) 0.1% ( +4dbu, gain: +66db, 48khz ) ” ( measured with a 18db / oct filter @80khz ) • frequency response 20hz to 20khz: max:+0.5db, min: 1.5db • dynamic range 107db ( typ. gain: 6db ) • crosstalk 100db ( @1khz ) • heat dissipation 55.9kcal / h max • power requirements ac100v 240v 50hz / 60hz • power consumption 65w • dimensions w 480mm h 88mm d 366mm • net weight 6.5kg • accessories included items = power cord, euro block plugs ( 3 pin, tabbed ) x16, euro block plugs ( 16 pin ) x2, cable ties, manual • others memory bank = preset: 50, phantom power = +48v 2 line up power amplifier 1 nos • amplifier type ( output circuitry ) class d thd+n 1khz, half power, 4ω , all channel output 0.2%, 1khz, half power, 100v, 70v • all channel output total 8 x 140w at 8ω / 4ω, 8 x 125w / 40ω 100v / 70v lines • 4 x 280w at double power mode ( 8ω / 4ω ) • frequency response 1w, 140w / 8ω, 20hz–20khz , 100v / 70v, 55hz–20khz crosstalk 1khz, half power, 8ω • att. max, input 150ω shunt 60db • residual noise a weighted , 280w, 8ω 65db , s / n ratio a weighted , 280w or 140w mode 100db • input sensitivity +4 db ( 1.23v ) • voltage gain 100v 38.2db , 70v 35.2db , 280w ( 140w ) / 8ω 31.7db, 560w ( 280w ) / 8ω 34.7db • load protection power switch on / off mute the output, dc fault power supply shutdown • amplifier protection thermal mute the output ( heatsink temp. 90°c ) ( return automatically. ) • overcurrent mute the output ( return automatically. ) • low load impedance mute the output ( return automatically. ) • power supply protection: thermal power supply shutdown ( heatsink temp. 100°c ) • integrated power gain reduction ( return automatically. ) • limiter circuit clip limiting clip limiter • cooling 3 speed fan x 2, front to back airflow • maximum input level +24dbu input impedance 20kω ( balanced ) 10kω ( unbalanced ) • sampling frequency 48khza / d, d / a converters ad: 24 bit linear, 128 times over sampling • signal processing 32 bit digital signal processing • latency setup = 0.25msec ) — 1.33msec 3 low profile ceiling speakers 8 4 slim line array speaker 2 nos • speaker type full range, bass reflex • component 1.5 (3.75 cm) cone × 16 • coverage ( 6db) horizontal: 170° • vertical: normal 25° (+12.5° to 12.5°) , • wide 30° (+12.5° to 17.5°) • effective coverage ( 10db) horizontal: 180° • vertical: normal 30° (+15° to 15°) , wide • 45° (+15° to 30°) • nominal impedance 12ω • power rating noise 80 w, pgm 160 w, max 320 w • sensitivity 1, 2 91db spl ,(90 db spl: with port cover),maximum spl 3 116 db spl (1 m) • frequency range ( 10 db) 1 81 hz 20 khz, (with port cover) 108 hz 20 khz • connector euro block (2 pin) × 2 (input: +/ ) • max. wire size awg12 (3.5 sq.) • vertical coverage selector normal/wide • overload protection full range power limiting to protect network, and transducers • magnetically shielded no • dust and water resistant ip34 (with port cover: ip35) • enclosure cabinet material : aluminium extrusion cabinet, • top/bottom board material abs (ul94 5vb) • metal grille perforated aluminium (t=1.0 mm) • aperture ratio: 55% • dimensions (w x h x d) speaker only 54 × 846 × 104 mm • with included bracket 54 × 846 × 111.5 mm • net weight speaker only 3.9 kg • packaging packaged in 1pc 5 (75) smart led screen 1 nos • display diagonal size1m 91cm (75), panel type new edge, 60hz, resolution3,840 x 2,160,pixel pitch (have)0.2451 x 0.2451 (mm), brightness (typical)350, contrast ratio4,000:1,viewing angle (h/v)178/178,response time8ms, colour gamut92%, glass haze0.02 %, h scanning frequency30 ~ 81khz, maximum pixel frequency594mhz, v scanning frequency48 ~ 75hz, contrast ratio (dynamic)mega • connectivity hdmi in2, dvi in1, usb2, ir in yes, audio in yes, audio out stereo mini jack, rs232 in yes, rs232 out yes, rj45 in yes, wifi yes, bluetooth yes • power power supplyac100 240v 50/60hz, power consumption (on mode)231, power consumption (sleep mode)0.5 w • dimension set dimension (wxhxd)1681.1 x 960.1 x 49.7 mm, package dimension (wxhxd)1871 x 1127 x 223 mm weight set weight38.3 kg, package weight49 kg • operation conditions temperature0℃~ 40℃, humidity10 ~ 80%, non condensing • mechanical specification vesa mount400 x 400 mm, bezel width11.5(top,side), 12.5(bottom), frame materialnon glossy • optional feature mountwmn6575se,wmn4277se • eco energy efficiency class n/a 6 low profile boundary microphones 7 mute button accessory 32 nos • connector type: 6 pin block connector • power requirements: phantom power • power consumption: 5 maw, maximum • weight: 113 g (0.25 lbs) • output configuration: active balanced • logic connections: led in active low (≤1.0v), ttl compatible. absolute maximum voltage: 0.7v to 50v. • logic out: active low (≤0.5v), sinks up to 20ma, ttl compatible. absolute maximum voltage: 0.7v to 24v (up to 50v through 3kω). • environmental conditions: operating temperature 5 to 45 °c (41 to 113 °f), storage temperature 29 to 74 °c ( 20.2 to 165 °f) relative humidity 0 95% • dimensions: base 3.74 x 3.74 x 1.06 in. (94.96 x 94.96 x 27.04 mm) h x w x d mute button: 1.54 x 2.67 x 0.2 in. (39.02 x 68 x 5.02 mm) h x w x d mute button tube: 0.87 x 0.87 x 3.03 in. (22 x 22 x 76.98 mm) h x w x d grommet: 1.97 x 1.97 x 0.31 in. (49.97 x 49.97 x 8 mm) h x w x d spacer:1.93 x 1.93 x 0.05 in. (49 x 49 x 1.2 mm) h x w x d 8 eight channel automatic mixer 4 nos • line headphone direct output: (typical, controls full clockwise), low impedance mic (150 ω) 80 db 88 db 34 db, line 40 db 48 db 6 db aux 44 db kω 52 db send/return 20 db 28 db inputs impedance • designed for use with typical output clipping level: mic 19 600 ω 1.6 kω 15 divoltine ≤2 kω 10 kω +22 dbv,aux ≤2 kω 10 kω +22 dbv,send/return ≤2 kω 10 kω +18 dbv • designed for use with typical output clipping level: line >600 ω 60 ω +18 dbv,headphone 8 200 ω, 60 ω recommended 300 ω +12 dbv, • designed for use with typical output clipping level: direct output >2 kω 1 kω +18 dbv, send/return >2 kω 1 kω +18 dbv, • total harmonic distortion: <0.1%at +18 dbvoutput level, 50 hz to 20 khz(through 20 hz 20 khz filter); input 1 and master at 5, all other controls • hum and noise: equivalent input noise 125 dbv(150 ω source; through 400 hz ,20 khz filter) equivalent input hum and noise 123 dbv(150 ω source; through 20 hz 20 khz filter) • output hum and noise through : 20 hz 20 khz filter; channel controls full counter clockwise • common mode rejection ratio :>70 db at 1 khz • polarity: mic/line, send inputs to all outputs are non inverting; aux input to all outputs is inverting • input channel activation :attack time 4 ms • hold time : 0.4 ms (switchable to 1.0 s) • decay time 0.5 s • off attenuation: 15 db (switchable to∞) • overload and shorting protection :shorting outputs, even for prolonged periods, causes no damage. microphone inputs are not damaged by signals up to 3 v; lines and monitor inputs by signals up to 20 v • equalization :low frequency 6 db/octavecut, adjustable corner from 25 to 320 hz • high frequency: ±6 dbat 5 khz, ±8 dbat 10 khz, shelvingat 5 • limiter :type peak • threshold switchable: off, +4, +8, +16 ( dbm at output) attack 2 ms recovery 300 ms indicator lights red when limiting occurs • input leds: green on channel activation, red at 6 dbbelow clipping • phantom power: 46 v dc open circuit through 6.8 k ω series resistance per din 45 596 • operating voltage : 230 v ac rated nominal, 50/60 hz, 100 ma • temperature range :operating temperature 0° to 60° c (32° to140° f) • storage temperature : 30° to 70° c ( 20° to165° f) • dimensions: 44.5 mm h x 483 mm w 317 mm d (1¾ x 19 x 12½ in.) 9 audio network interface 2 10 audio conferencing processor 1 nos • input (2) 3 pin block connector (active balanced) • output (2) 3 pin block connector (impedance balanced) • mobile (1) trrs 3.5 mm (1/8) • usb connections :(1) usb 2.0, type b • single port carries : 2 input and 2 output channels (summed mono) • network connections (dante digital audio):(1) rj45,10 dante inputs , 8 dante outputs • polarity: non inverting, any input to any output • power requirements: 802.3 at type 2 (poe plus), class 4 • power consumption: 17.5 w, maximum • weight: 1710 g (3.8 lbs) • dimensions :h x w x d 4 x 21 x 22.6 cm (1.6 x 8.3 x 8.9 in.) • control software: designer • operating temperature range: −6.7°c (20°f) to 50°c (122°f) • storage temperature range: −29°c ( 20°f) to 74°c (165°f) • thermal power dissipation: maximum 17.5 w (60 btu/hr) typical 14.6 w (50 btu/hr) • audio frequency response: +1, 1.5 db 20 to 20,000 hz • dante digital audio: sampling rate 48 khz bit depth 24 • usb audio: sampling rate 48 khz bit depth 16, 24 • latency: does not include dante latency • analog connections: (block connectors) • dynamic range:20 hz to 20 khz, a weighted, typical analog to dante 113 db dante to analog 117 db • equivalent input noise: 20 hz to 20 khz, a weighted, input terminated with 150ω line 86 dbv aux 98 dbv • total harmonic distortion: @ 1 khz, 0 dbv input, 0 db analog gain <0.05% • common mode rejection ratio: 150ω balanced source @ 1 khz >50 db • input impedance: 9.6 kω • input clipping level: line +27 dbv aux +15 dbv • output impedance: 80 ω • output clipping level:line +20 dbv aux +0 dbv mic 26 dbv 1.4 kω • output clipping level: output terminated with 2.2 kω 11 smart managed switch 1 nos • 1000base t interface:12 • auto mdi/mdix:yes • 1000base t poe interface:12 • 10/100/1000base t poeports:12 • 10/100/1000base t ports:12 • switch capacity:48 gbps • max. packet forwardingrate:35.71 mpps • power input:ac: 100 240v • comply with rohs 6: yes • energy efficiency ethernet(eee):yes • power saving by link status: yes 12 motorized retractable monitor lift with integrated screen 15 nos • material full aluminum alloy • panel size 680*80*smm • case size 667*71*730mm • panel thickness smm aluminum panel • integrated monitor 18.5 inch led monitor screen • resolution 1280*720 hd • screen size 488*280*15mm • screen tilt angle automatic 0 15 degree /eiectric adjustable 0 30 degree • color brushed aluminum silver / aluminum black matte • connection interface hdmi, usb, rs232 i/o • full hd touch screen conference system discussion/video/voting microphone • full hd camera :smart aio pc • safe protection office automatic paperless system: anti pinch hand protection o weight :16kgs o power :220v/50hz, 110v/60hz 28w • service life: above 20000 times • working sound less than 15 decibels • certification: ce,rohs, iecc. cb. fcc • monitor: size 18.5 inch led screen,format16: 9, resolution1280*720, viewing angle80/40, pixel resolution0.2,frequency60hz,brightness300,contrast ratio600: 1,response time16 ms ,display color16.7 m (10 bit), power consumption 245,speed 120,voltage12, materialtft 13 hdmi matrix routing switcher 1 nos • type of hdmi switcher: (16) hdmi inputs to (16) hdmi outputs matrix switcher • hdmi support: hd 1080p@60hz, 4k2k@30hz, h36 bit deep color, 3d (1.4a) formats • hdcp / cec support: hdcp 1.3 & cec compliant • video bandwidth: double data rates: 340mhz, total 6.7gbps bandwidth • digital video support: hd: 480i/ 480p/ 720p/ 1080i/p and 4k2k@30hz up to 36bit deep color • inputs (hdmi): (16) hdmi (hdmi or dvi digital source) • outputs (hdmi): (16) hdmi (to destination) • digital audio support: multi audio formats 5.1 / 7.1, mat(mlp), dolby digital, dolby truehd, dolby digital plus, dts, dts es 6.1, dts hd, dts hd hra, dts hd master, (pcm 2ch) • booster (each hdmi output port): *1080p up to ~98 feet (30m) & 4k2k@30hz up to ~49 feet (15m) • switcher controls: • select & function buttons on front panel (data status via lcm panel show out) • ir remote control (switch control) (sw 5669) • ir external port (switch control via 3.5mm od jack) • rs 232 series interface (switch control) • ethernet series interface (switch control) • source status: input status leds indicates presence of a live signal • (39) function control keys: 1. all, 2. off, 3. recall, 4. enter, 5. memory, 6. lock, 7. edid, 8. destination 1 thru 16, 9. source 1 thru 16 • learning mode: • 1. select learning mode 1: learning single destination edid to link source • 2. select learning mode 2: learning multiple destination edid to link source • infrared frequency: 38khz • ir extend distance: sb 100 (~984 ft / 300m max), sb 100c (~6.5 ft/2m) • hdbaset™ extender distance: ~328 ft / 100m max • hdmi i/o connector: hdmi type a smd 19pin female type • temperature: operating temperature 32°f 100°f (0°c 32°c) • dimensions (lxwxh): 17.5 x 12 x 3.5 in • rack mount: 2ru high 19 in rack mount (with rack mount ears) #2u 440l • power supply: ac 100~240vac 50/60hz (120v/1a/120w; 220v/0.54a/120w) • unit material: metal (thin 1mm) • safety approvals: ce, fcc, reach • weight: 11.2 lb (unit only) / 16.8 lb (net) 14 hdmi kvm+ ir extender 24 nos • use single utp cable( cat 5e/6 , should follow eia /tia 568 b standard ) to substitute hdmi cable to extend longer transmission distance • support 8 kesd protection • support msd equalisation and enhancement • support edid pass through via lan for the best compliances with most display device • support infrared control signal pass through via lan • by transmitting keyboard and mouse details via lan it is easy to control pc • support 1080 p 60 hertz resolution transmission via up cable up to 60 metre 15 high speed hdmi interconnects 50 nos • hdmi certification: ≤ 3.0m lengths • hdmi cts certification: high speed with ethernet • certified data rate: 3.4gbpsc, 10.2gbps aggregate • supported data rate: > 3.4gbpsc (4k uhd) • supported hdmi clock: 27 340mhz • length 2 mtr 16 digital microphone cable 17 category 6 type cable 305 mtr. • product number 1071e • ansi/tia category 6 • cable component type horizontal • cable type u/utp (unshielded) • conductor type, singles solid • conductors, quantity 8 • pairs, quantity 4 • separator type bisector • transmission standards ansi/tia 568.2 d | cenelec en 50288 6 1 | iso/iec 11801 class e • dimensions • diameter over insulated conductor 1.029 mm | 0.041 in • diameter over jacket, nominal 5.893 mm | 0.232 in • jacket thickness 0.559 mm | 0.022 in • conductor gauge, singles 23 awg 18 integrator series speaker cable 305 mtr. • engineered and constructed to ensure installation success and ease, • 99.99% oxygen free copper (ofc), • low smoke zero halogen (lszh) construction, • easy glide yellow, purple & black outer j acket, • sturdy easy pull reel box, • metre marked, • easy strip internal nylon rip cord, • avalable in 2 core conductors, • available in 14 wire gauge, • industry standard colour coding (red, black, green, white) • cpr declared performance: eca (en 50575:2014+a1:2016) 19 wireless conferencing unit 1 nos • operating system windows 10 or higher macos 11 (bigsur) and higher • android v11 and higher (clickshare app) • ios 14 and higher (clickshare app) • system requirements for a smooth experience with microsoft teams or zoom • minimum: intel i3 dual core processor / 8gb ram / os : windows 10 latest build or mojave latest build • recommended: intel i5 4 core processor / 8gb ram / os: windows 10 latest build or mac os latest • build • video outputs 4k uhd (3840*2160) @ 30hz. hdmi 1.4b • video inputs 1920x1080 @30hz. hdmi 1.4b • audio output usb, spdif, jack, hdmi • connections 1x ethernet lan 1gbit • 1x usb c 2.0 (back); 2x usb a 2.0 (back); 1x usb a 2.0 (front) • noise level max. 25dba @ 0 30°c • max. 30dba @ 30 40°c • authentication protocol wpa2 psk in stand alone mode • wpa2 psk or ieee 802.1x using the clickshare button in network integration mode • wireless transmission protocol ieee 802.11 a/g/n/ac and ieee 802.15.1 • reach max. 30m (100 ft) between clickshare button and clickshare base unit • frequency band 2.4 ghz and 5 ghz (dfs) • frequency band 2.4 ghz and 5 ghz (dfs channels supported in select number of countries) • temperature range operating: 0°c to +40°c (+32°f to +104°f) • max: 35°c (95°f) at 3000m • storage: 20°c to +60°c ( 4°f to +140°f) • humidity storage: 0 to 90% relative humidity, non condensing • operation: 0 to 85% relative humidity, non condensing • anti theft system kensington lock • certifications fcc/ce • touch screen support & interactivity yes • wireless conferencing via app or button • local view high quality • network connection lan & wifi (dual) • management and reporting yes • warranty 1 year standard. 5 years coverage via smartcare 20 av/network server rack 1 nos • 32u server racks 600 mm width x 1000 mm depth with front glass door • back steel door/ side detachable panels/ wheels • fan housing unit 4 fan • keyboard tray sliding and rotary • monitor shelf • additional equipment shelf • cable manager horizontal • power strip 12 socket 5 amp • mounting hardware usability network switches/routers/ dvr/ audio visual equipment/broadcasting equipment /servers • front door glass door or full perforated with lock • rear door half perforated and full perforation steel door with lock • side panels removable with slam latch and lockable provision • cable entry cut top/ bottom • 4 pair heavy duty (2.0mm) depth support channel fitted on front & rear pillar • 2 pair heavy duty (2.0mm) vertical mounting rail channel fitted on front & rear pillar • cooling option 4 fan provision mounted on top panel • load bearing capacity up to 400 to 600 kg • construction dismantle construction overall 1.2mm thick (18 gauge), load bearing angles are 2 mm • power distribution unit horizontal vertical optional • cable management horizontal & vertical • sliding tray for equipment and keyboard optional • color light grey powder coated ( ral 7035) and ral 9005 black ( as per requirement) 21 air condition & colling equipment 5 nos • unit type : ceiling mount • star rating :1 • compressor performance type / refrigerant: rotary / r22 • rated cooling capacity (100%load): btu / hr 17422 • rated cooling capacity (100%load) watts: 5100 • rated iseer: 3.35 • annual power consumption as per bee norms (kwh): 1178 • fan speed no. of steps: 4 • air flow (idu) (cooling super high) cfm (high): 550 • sound level (dba) (l/h ) : 37 • rated power input cooling watts : 1522 • rated power supply volts / hz /phase : 230 / 50 / 1 • rated current drawn amps : 6.97 • suction line diameter inches (mm) : 5/8” (15.88) • liquid line diameter inches (mm) : 1/4” (6.35) • remocon type: lcd cordless. 22 acoustics & sound isolation work 1386 sqft • existing walls should be acoustically treated using gypsum based acoustical treatment. • the treatment shall consist of 75mm thick treatment with 12.5mm thick gypsum aoustical aperture board made out of gi framework as per igls specifications with glass wool / rock wool material 48 kg density. • the frame work should be adequately anchored in the wall/floor. acoustic insulation in partition frame work shall be 50mm thick glass wool / rock wool of designed density, tied to the frame etc. forming high frequency absorbers. • the partition framework shall be covered from all sides with bass traps / low frequency absorbing treatment and entire treatment would be finished to receive paint. • bass traps: gypsum wall frame work shall be covered from all sides with bass traps / low frequency absorbing treatment. the entire surface would be painted. 23 conference camera 1 nos 120 degree hfov, 70 degree hfov 140 degree dfov, 78 degree dfov • 20 megapixel sensors • camera range up to 25 ft/7.62 m • 7.3x digital zoom • uhd 2160p (4k) capture resolution • automatic meeting experience powered by poly director ai smart camera technology including group framing, people framing (preview feature), and speaker framing 24 installation & integration of above av & vc product 1 job • sitc related xlr / phono/ponix connectors approx ( 100 nos) • sitc of all mentioned material on required existing place • integration / connection / & programming of all mentioned material • proper winding of all cable behind server rack & under conference table 25 on site demo , training & service support 1 job • proper demonstration of working equipment’s after integration • operational training provide to it team for seamless operation of all equipment • service visit on quarterly basis (1 visit / per quarter ) to ensure technical support on site • technical assistance ( on phone ) regarding warranty & maintenance or periodic service if arise within a year period. 26 pop ceiling work 1700 sq ft labor charges for pop work as per requirement 27 carpentry work 1 job labor charges for carpentry work as per requirement 28 electrical work 1 job • sitc of all mentioned material on required existing place • connection & all mentioned material • proper wiring of all cable behind server rack & under conference table 29 installation & wiring of online ups ...

Ministry Of Tourism - Delhi

37350921 bids are invited for aluminium and aluminium alloy bare foil for food packaging is:15392 ( q3 ) total quantity : 1000...

Department Of Defence - Delhi

37265725 bids are invited for machineries of carpenter for iti school foot rule or steel tape , foot rule or steel tape , foor rule or steel tape , steel measuring scale , marking knife , try square machinist steel square , premium aluminum alloy double side , bevel square wooden , carpenter marking gauge , carpenter mortise gauge , hand saw , tenon saw , metal jack plane , metal smoothing plane , firmer chisel , mortise chisel , screw driver , mallet medium size , claw hammer , oil stone carborundum universal silicon carbide combination rough and fine , hand brush for cleaning , construction scale ss , spring caliper inside , spring caliper outside , wing compass , trammel , sprit level , rip saw , cross cut saw , key hole saw , fret saw frame , compass saw , carpenter adze , trying plane metal , plane rivet adjustable , plough plane , spoke shaves , plane adjustable circular , router plane , moulding plane set , cabinet scraper , gauge chisel firmer 6 mm , gauge chisel firmer 10 mm , gauge chisel firmer 12 mm , gauge chisel firmer 16 mm , gauge chisel firmer 20 mm , gauge chisel scribing 6 mm , gauge chisel scribing 10 mm , gauge chisel scribing 12 mm , gauge chisel scribing 16 mm , gauge chisel scribing 20 mm , ball pein hammer 600 gms , cross pein hammer 600 gms , pincer 50 mm , file half round 2nd cut 250 mm , file half round wood rasp bastard250mm , file slim taper 100 mm , file slim tape 150 mm , card file steel wire brush for file 200 mm , hands drill double pinion steel drill chuck drive sizes 6 mm to 10 mm , country drill with bow ball bearing type 620 x 726 mm , ratchet brace 250 mm swap , hand auger 10 mm , hand auger 12 mm , hand auger 14 mm , hand auger 16 mm , hand auger 18 mm , hand auger 20 mm , hand auger 22 mm , hand auger 25 mm , centre bits 6 mm , centre bits 8 mm , centre bits 10 mm , centre bits 12 mm , expansion bit sets 218 x 171 mm , twist drill bits 6 mm , twist drill bits 8 mm , twist drill bits 10 mm , twist drill bits 2 mm , counter sink bit rose type 12 1 9910 mm , twist drill bits 2 mm , counter sink bit rose type 12 side cutting pliers 250 x 250 mm , plunger saw set or pistol grip type 300 x 300 mm , number punch 12 mm , slip stone 100 mm , round crow bar with chisel and claw end 1070 x 25mm , g clamp 100 mm , g clamp 150 mm , g clamp 250 mm , t bar cramp 0 6 meter , t bar cramp 1 25 meter , t bar cramp 1 75 meter , carpenter vice material cast iron item dimensions lxwxh 15 x 10 x 5 centimeters style heavy duty heavy duty cast iron material used , saw sharpening vice 250 jaws , carving tools set , glass cutter , nail punch , surface plate 600x 600 mm , carpenter s wooden work bench 2400x920x800 mm height smooth finishedpolished , grease gun , spanner double ended , portable circular saw machine , portable planning machine , power drill machine industrial type , portable sander machine electric , portable jig saw machine , portable router machine industrial type , power screw driver , combined surface and thickener , circular saw machine , lathe wood turning , tenoning machine single ended , mortising machine combine hollow chisel and chain , bench grinder 200 mm whole d e pedestal , drill machine , portable electric drill wolf type , drills chuck , portable disc sander , adjustable saw sharpener , electric heater 1000 or 1500 w 1 nos 102 electric blower portable , moisture meter , universal wood working machine , electrical drying oven , vertical bandsaw machine , cd and dvd of different joint related to carpenter works and variety design of modern furniture , providing and laying steel office almirah small , providing and laying glass door almirah , providing and laying steel table for class rooms , providing and laying steel table with cubboard officer , providing and laying automation table l type class i officer , providing and laying computer table , providing and laying chair with arms , providing and laying executive rev chair high back , providing and laying centre table , providing and laying sofa set 3 1 1 seater , vertical support for desk , providing and laying self contained drinking water cooler of 150 ltrs supply installation and commissioning of tools and total quantity : 1485...

Public Works Department - Delhi

36941714 up gradation / modification of substation equipment at jail no. 8 / 9, tihar jail, delhi 1 main lt panel supplying, installation, testing & commissioning of cubical modular type lt panel suitable for 415 v, 3 phase, 4 wire 50 hz ac supply system fabricated in compartmentalized design having bus bar chamber duly fabricated from crca sheet steel of 2 mm thick for frame, back, sides, partition & doors and 3mm thick for glad plate duly powder coated in approved shade including cleaning & finishing complete with 7 tank process complete with2000 amp capacity extensible type four strip aluminium alloy bus bars of hight conductivity, dmc/ smc bus bar supports having short circuit withstand capacity of 31 mva for 1 sec., bottom base channel of ms section not less than 100 mm x 50 mm x 5 mm thick, entire panel shall have a common earth bar of size 25 mm x 5 mm at the rear with 2 nos. earth stud, solid connections from main bus bar to switch gears with required size of al. bus bars, control wiring with2.5 sq. mm. pvc insulated copper conductor single core cable, cooling / ventilation fans including construction of suitable cc foundation, in & out connections and providing & fixing following switch gears therein etc. complete as required. (i/c credit of the dismantled lt panel to the agency) 2 incoming t/f 1 & 2 3 (i) 2 nos 1600 ampers four pole horizontal drawout type electrically operated air circuit breaker of fault breaking capacity 50 ka breaking capacity (ics = icu = icw=100%) for 1 second suitable upto 690v, fitted with interlocked door, automatic safety shutters, mechanical on/off and service/test/isolated position indicators and frame earthing contact, auxilary contacts, shunt trip, interlocking features etc. complete with self powered microprocessor based release for adjustable setting for over current, earth fault & short circuit protection with lcd display & pre overload and over temperature protection indication & all other standard features conforming to is 1397 2 : 1993 as amended up to date(ii) 2 sets ryb phase indication led lamps with 6a, 10ka, c curve back up mcb, breaker on/off/trip indicating light with 6a, 10ka, c curve backup mcb(iii) 2 nos. 3 phase intelligent multifunction digital meter to read v, a, kva, kwh, pf hz etc. with 3 nos. resin cast cts of 1600/5 a class 1.0 accuracy and 15 va burden and with 3 nos 6a, 10ka, c curve back up mcb. 4 incoming d/g 1 & 2 5 (i) 2 nos 1000 ampers four pole horizontal drawout type electrically operated air circuit breaker of fault breaking capacity 50 ka breaking capacity (ics = icu = icw=100%) for 1 second suitable upto 690v, fitted with interlocked door, automatic safety shutters, mechanical on/off and service/test/isolated position indicators and frame earthing contact, auxilary contacts, shunt trip, interlocking features etc. complete with self powered microprocessor based release for adjustable setting for over current, earth fault & short circuit protection with lcd display & pre overload and over temperature protection indication & all other standard features conforming to is 1397 2 : 1993 as amended up to date 6 (ii) 2 sets ryb phase indication led lamps with 6a, 10ka, c curve back up mcb, breaker on/off/trip indicating light with 6a, 10ka, c curve backup mcb(iii) 2 nos. 3 phase intelligent multifunction digital meter to read v, a, kva, kwh, pf hz etc. with 3 nos. resin cast cts of 1000/5 a class 1.0 accuracy and 15 va burden and with 3 nos 6a, 10ka, c curve back up mcb. 7 bus coupler 8 (i) 1 nos 1600 ampers four pole horizontal drawout type electrically operated air circuit breaker of fault breaking capacity 50 ka breaking capacity (ics = icu = icw=100%) for 1 second suitable upto 690v, withoutrelease, fitted with interlocked door, automatic safety shutters, mechanical on/off and service/test/isolated position indicators and frame earthing contact, auxilary contacts, shunt trip, interlocking features etc.(ii) 1 sets ryb phase indication led lamps with 6a, 10ka, c curve back up mcb, breaker on/off/trip indicating light with 6a, 10ka, c curve backup mcb 9 interlocking 10 (i) electrical interlocking through advance contacts in acbs (all incomers & bus couplers)along with mechanical interlocking 11 outgoing 12 (i) 2 nos. 800 ampers four pole horizontal drawout type electrically operated air circuit breaker of fault breaking capacity 50 ka breaking capacity (ics = icu = icw=100%) for 1 second suitable upto 690v, fitted with interlocked door, automatic safety shutters, mechanical on/off and service/test/isolated position indicators and frame earthing contact, auxilary contacts, shunt trip, interlocking features etc. complete with self powered microprocessor based release for adjustable setting for over current, earth fault & short circuit protection with lcd display & pre overload and over temperature protection indication & all other standard features conforming to is 1397 2 : 1993 as amended up to date 13 (ii) 2 sets ryb phase indication led lamps with 6a, 10ka, c curve back up mcb, breaker on/off/trip indicating light with 6a, 10ka, c curve backup mcb(iii) 2 nos. 3 phase intelligent multifunction digital meter to read v, a, kva, kwh, pf hz etc. with 3 nos. resin cast cts of 800/5 a class 1.0 accuracy and 15 va burden and with 3 nos 6a, 10ka, c curve back up mcb. 14 (ii) 8 set 630a, fp, 36ka mccb (ics=icu =100%)withthermal magnetic based release with adjustable settinghaving o/l & s/c protection with rotary handle and spreader terminal.(iii) 6 set 400a, fp, 36ka mccb (ics=icu =100%)withthermal magnetic based release with adjustable settinghaving o/l & s/c protection with rotary handle and spreader terminal.(iv) 4 set 250a, fp, 36ka mccb (ics=icu =100%)withthermal magnetic based release with adjustable settinghaving o/l & s/c protection with rotary handle and spreader terminal. 15 transformer supplying, installation, testing & commissioning of 630kva, 11/0.433kv, 3ph, 50hz, dyn 11, indoor onan type, copper wound transformer with off load tap changing arrangement on hv side in steps of +/2.5% & 7.5%,having cable end boxes on hv side suitable for 3x400sq mm xlpe cable of 11kv grade and 1600a bus trunking arrangement on lv side complete with all accessories i/c first filling of filtered dehydrated oil and confirming to is 2026 (part 1 to part 5) & as per specification attached complete in all respects as required at site. (i/c credit of dismantled transformer to the agency) 16 bustrunkingsupplying, installing, testing and commissioning of 1600a air insulated compact type bus duct suspended on ceiling for use on 3 phase 4 wire 415 volts, 50hz a.c. supply with metal clad enclosure having ip 54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 nos aluminium bus bars having current density of 130 a/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints, fire barrier at each floor, continuous earthing with 2 nos aluminium strip of suitable size (one on each side) including, g.i. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. (i/c credit of the dismantled bus trunking to the agency) 17 earthingearthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required. 18 providing and fixing 25 mm x 5 mm copper strip in 40 mm dia g.i. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re filling etc. as required. 19 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required. 20 providing and fixing 25 mm x 5 mm g.i. strip in 40 mm dia g.i. pipe from earth electrode including connection with g.i. nut, bolt, spring, washer excavation and re filling etc. as required. 21 cablesupplying & fixingof following size xlpe insulated and pvc sheathed aluminium conductorarmoured power cable of 1.1 kv grade conf. to is 7098 (part i)in the following ways etc complete as required. 22 3.5 x 400 sq.mm 23 3.5 x 185 sq.mm 24 3.5 x 120 sq.mm 25 3.5 x 95 sq.mm 26 supplying and making end termination with brass compression gland and aluminium lugs for following size of pvc insulated and pvc sheathed / xlpe aluminium conductor cable of 1.1 kv grade as required. 27 3½ x 400 sq. mm (82mm) 28 3½ x 185 sq. mm (57mm) 29 3½ x 120 sq. mm (45 mm) 30 3½ x 95 sq. mm (45 mm) 31 misc. civil workproviding and laying in position cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation of pump, dg set etc. including form work etc. as required. 32 excavation of the cable trenches in hard rock not exceeding 1.5 meter in width, and lift upto 1.5 meter, including getting out the excavated soil and disposal of excavated soil as directed within a lead of 50 meter. 33 providing brick work (in width 225 mm or more) with f.p.s. bricks of class designation 7.5 in cement mortar 1:4 (1 cement : 4 coarse sand) at all levels. 34 providing 15 mm thick cement plaster of mix 1:4 (1 cement : 4 fine sand) at all levels. ...

Public Works Department - Delhi

36929241 up gradation / modification of substation equipment at jail no. 1, tihar jail, delhi 1 main lt panel 2 supplying, installation, testing & commissioning of cubical modular type lt panel suitable for 415 v, 3 phase, 4 wire 50 hz ac supply system fabricated in compartmentalized design having bus bar chamber duly fabricated from crca sheet steel of 2 mm thick for frame, back, sides, partition & doors and 3mm thick for glad plate duly powder coated in approved shade including cleaning & finishing complete with 7 tank process complete with2500 amp capacity extensible type four strip aluminium alloy bus bars of hight conductivity, dmc/ smc bus bar supports having short circuit withstand capacity of 31 mva for 1 sec., bottom base channel of ms section not less than 100 mm x 50 mm x 5 mm thick, entire panel shall have a common earth bar of size 25 mm x 5 mm at the rear with 2 nos. earth stud, solid connections from main bus bar to switch gears with required size of al. bus bars, control wiring with2.5 sq. mm. pvc insulated copper conductor single core cable, cooling / ventilation fans including construction of suitable cc foundation, in & out connections and providing & fixing following switch gears there in etc. complete as required. (i/c credit of dismantled panel to the agency) 3 incoming 4 (i) 2 nos 2000 ampers four pole horizontal drawout type electrically operated air circuit breaker of fault breaking capacity 50 ka breaking capacity (ics = icu = icw=100%) for 1 second suitable upto 690v, fitted with interlocked door, automatic safety shutters, mechanical on/off and service/test/isolated position indicators and frame earthing contact, auxilary contacts, shunt trip, interlocking features etc. complete with self powered microprocessor based release for adjustable setting for over current, earth fault & short circuit protection with lcd display & pre overload and over temperature protection indication & all other standard features conforming to is 1397 2 : 1993 as amended up to date(ii) 2 sets ryb phase indication led lamps with 6a, 10ka, c curve back up mcb, breaker on/off/trip indicating light with 6a, 10ka, c curve backup mcb(iii) 2 nos. 3 phase intelligent multifunction digital meter to read v, a, kva, kwh, pf hz etc. with 3 nos. resin cast cts of 2000/5 a class 1.0 accuracy and 15 va burden and with 3 nos 6a, 10ka, c curve back up mcb. 5 bus coupler 6 (i) 1 nos 2000 ampers four pole horizontal drawout type electrically operated air circuit breaker of fault breaking capacity 50 ka breaking capacity (ics = icu = icw=100%) for 1 second suitable upto 690v, withoutrelease, fitted with interlocked door, automatic safety shutters, mechanical on/off and service/test/isolated position indicators and frame earthing contact, auxilary contacts, shunt trip, interlocking features etc.(ii) 1 sets ryb phase indication led lamps with 6a, 10ka, c curve back up mcb, breaker on/off/trip indicating light with 6a, 10ka, c curve backup mcb. 7 interlocking 8 (i) electrical interlocking through advance contacts in acbs (all incomers & bus couplers)along with mechanical interlocking 9 outgoing 10 (i) 3 nos. 1600 ampers four pole horizontal drawout type electrically operated air circuit breaker of fault breaking capacity 50 ka breaking capacity (ics = icu = icw=100%) for 1 second suitable upto 690v, fitted with interlocked door, automatic safety shutters, mechanical on/off and service/test/isolated position indicators and frame earthing contact, auxilary contacts, shunt trip, interlocking features etc. complete with self powered microprocessor based release for adjustable setting for over current, earth fault & short circuit protection with lcd display & pre overload and over temperature protection indication & all other standard features conforming to is 1397 2 : 1993 as amended up to date.(ii) 3 sets ryb phase indication led lamps with 6a, 10ka, c curve back up mcb, breaker on/off/trip indicating light with 6a, 10ka, c curve backup mcb(iii) 3 nos. 3 phase intelligent multifunction digital meter to read v, a, kva, kwh, pf hz etc. with 3 nos. resin cast cts of 1600/5 a class 1.0 accuracy and 15 va burden and with 3 nos 6a, 10ka, c curve back up mcb.(ii) 10 set 630a, fp, 36ka mccb (ics=icu =100%)withmicroprocessor based release with adjustable settinghaving o/l & s/c protection with rotary handle and spreader terminal. (iii) 10 sets on/offindicating light with 6a, 10ka, c curve backup mcb, auxiliary contacts with mccb 11 emergency panel 12 supplying, installation, testing & commissioning of cubical modular type lt panel suitable for 415 v, 3 phase, 4 wire 50 hz ac supply system fabricated in compartmentalized design having bus bar chamber duly fabricated from crca sheet steel of 2 mm thick for frame, back, sides, partition & doors and 3mm thick for glad plate duly powder coated in approved shade including cleaning & finishing complete with 7 tank process complete with2500 amp capacity extensible type four strip aluminium alloy bus bars of hight conductivity, dmc/ smc bus bar supports having short circuit withstand capacity of 31 mva for 1 sec., bottom base channel of ms section not less than 100 mm x 50 mm x 5 mm thick, entire panel shall have a common earth bar of size 25 mm x 5 mm at the rear with 2 nos. earth stud, solid connections from main bus bar to switch gears with required size of al. bus bars, control wiring with2.5 sq. mm. pvc insulated copper conductor single core cable, cooling / ventilation fans including construction of suitable cc foundation, in & out connections and providing & fixing following switch gears therein etc. complete as required. (i/c credit of dismantled panel to the agency) 13 incoming 14 (i)3 nos. 1600 ampers four pole horizontal drawout type electrically operated air circuit breaker of fault breaking capacity 50 ka breaking capacity (ics = icu = icw=100%) for 1 second suitable upto 690v, fitted with interlocked door, automatic safety shutters, mechanical on/off and service/test/isolated position indicators and frame earthing contact, auxilary contacts, shunt trip, interlocking features etc. complete with self powered microprocessor based release for adjustable setting for over current, earth fault & short circuit protection with lcd display & pre overload and over temperature protection indication & all other standard features conforming to is 1397 2 : 1993 as amended up to date(ii) 3 sets ryb phase indication led lamps with 6a, 10ka, c curve back up mcb, breaker on/off/trip indicating light with 6a, 10ka, c curve backup mcb(iii) 3 nos. 3 phase intelligent multifunction digital meter to read v, a, kva, kwh, pf hz etc. with 3 nos. resin cast cts of 1600/5 a class 1.0 accuracy and 15 va burden and with 3 nos 6a, 10ka, c curve back up mcb. 15 bus coupler 16 (i) 2 nos 1600 ampers four pole horizontal drawout type electrically operated air circuit breaker of fault breaking capacity 50 ka breaking capacity (ics = icu = icw=100%) for 1 second suitable upto 690v, withoutrelease, fitted with interlocked door, automatic safety shutters, mechanical on/off and service/test/isolated position indicators and frame earthing contact, auxilary contacts, shunt trip, interlocking features etc.(ii) 2 sets ryb phase indication led lamps with 6a, 10ka, c curve back up mcb, breaker on/off/trip indicating light with 6a, 10ka, c curve backup mcb 17 interlocking 18 (i) electrical interlocking through advance contacts in acbs (all incomers & bus couplers)along with mechanical interlocking 19 outgoing 20 (i) 3 sets 630a, fp, 36ka mccb (ics=icu =100%)withmicroprocessor based release with adjustable settinghaving o/l & s/c protection with rotary handle and spreader terminal. (ii) 12 sets 400a, fp, 36ka mccb (ics=icu =100%)withmicroprocessor based release with adjustable settinghaving o/l & s/c protection with rotary handle and spreader terminal. (iii) 8 sets 250a, fp, 36ka mccb (ics=icu =100%)withmicroprocessor based release with adjustable settinghaving o/l & s/c protection with rotary handle and spreader terminal. (iv) 8 sets 200a, fp, 25ka mccb (ics=icu =100%)withthermal magnetic based release with adjustable settinghaving o/l & s/c protection with rotary handle and spreader terminal. (v) 8 sets 160a, fp, 25ka mccb (ics=icu =100%)withthermal magnetic based release with adjustable settinghaving o/l & s/c protection with rotary handle and spreader terminal(vii) 39 sets on/off/ indicating light with 6a, 10ka, c curve backup mcb, auxiliary contacts with mccb. 21 bustrunking 22 supplying, installing, testing and commissioning of following capacity air insulated compact type bus trunking suspended on ceiling for use on 3 phase 4 wire 415 volts, 50hz a.c. supply with metal clad enclosure having ip 54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 nos aluminium bus bars having current density of 130 a/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints, fire barrier at each floor, continuous earthing with 2 nos aluminium strip of suitable size (one on each side) including, g.i. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. (i/c credit of the dismantled bus trunking to the agency) 23 dg set 24 providing, installing, testing and commissioning of ‘silent type’ diesel generating set alongwith having prime power rating of 1010kva, 415 volts at 1500 rpm, 0.8 lagging power factor at 415 v suitable for 50 hz, 3 phase system & for 0.85 load factor, is/iec 60034 1,is 1460, iso 8528, iso 3046, is 13018, iso 9001 standards and consisting of the followings: (i/c credit of dismantled 380kva dg set to the agency) 25 diesel engine: 26 diesel engine 4 stroke water cooled, electric start, of suitable bhp at 1500 rpm suitable for above output of alternator at 40 degree c, 50% rh & at 1000 meter msl and conforming to iso 3046, capable of taking 10% over loading for one hour after 12 hours of continuous operation. the engine will be fitted complete with all the required accessories. 27 engine mounted instrument panel fitted with and having digital display for following: (i) start stop switch with key (ii) water temperature indication (iii) lubrication oil pressure indication (iv) lubrication oil temperature indication (v) battery charging indication (vi) rpm indication (vii) over speed indication (viii) low lub. oil trip indication (ix) engine hours indication 28 alternator : 29 synchronous alternator rated at1010kva, 415 volts at 1500 rpm, 3 phase 50 hz, ac supply with 0.8 lagging power factor at 40 degree c, 50% rh & at 1000 meter msl. the alternator shall be having spdp enclosure, brushless, continuous duty, self excited and self regulated through avr conforming to is/iec 60034(i) suitable for tropical conditions and with class f/h insulation. 30 base frame & foundation: 31 both the engine and alternator shall be mounted on suitable base frame made of ms channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of manufacturer. 32 fuel tank: 33 daily service fuel tank of 990 liters capacity fabricated out of 3 mm thick m.s. sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with ms class ‘c’ pipes of suitable dia. complete with valves, level indications & accessories as required as per specifications. 34 exhaust system: 35 dry exhaust mainfold with hospital exhaust silencer and catalytic convertor. 36 starting system: 37 12v/24v dc starting system comprising of starter motors: voltage regulator and arrangement for initial excitation complete with suitable nos. of batteries (25 plates, 180 amp. hour capacity lead acid type) as required as per specifications. 38 accoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air in to the atmosphere as per specifications. 39 amf panel 40 fabricating, installing, testing & commissioning of automatic mains failure control including auto by pass panel, suitable for 1010 kva silent type dg set complete with relays, timers, set of cts for metering & protection and energy analyser to indicate currents, phase and line voltages, frequency, power factor, kwh, kvarh & provision for overload, short circuit, restricted earth fault, under frequency, control cabling from amf panel to diesel engine and elsewhere if required, all complete and interlocking including the following: (i/c credit of dismantled amf panel to the agency) 41 (a) 02nos. 1600amp., motorised electrically operated draw out with cradle type 3 position acb with microprocessor based release for o/c & e/f and shunt trip. 42 (b) auto/manual/test/off selector switch 43 (c) 2 nos. over voltage relay, 2 nos. reverse power relay and 2 nos. under voltage relay. 44 (d) 3 sets of current transformers 15 p 10 accuracy for protection and 15 va class i for metering 45 (e) energy analyser unit to indicate current voltage frequency power factor and kwh 46 (f) indicating lamps for load on mains and load on set 47 (g) fuse for instruments 48 (h) battery charger, complete with transformer/ rectifier, d.c. voltmeter and ammeter, selector switch for trickle, off and boost and current adjustment. 49 (i) main supply failure monitor 50 (j) supply failure timer 51 (k) restoration timer 52 (l) control unit with three impulse automatic engine start/stop and failure to start lockout. 53 (m) impulse counter with locking and reset facility. 54 (n) on/off/control circuit switch with indicator 55 (o) audio/video annunciation for (i) high water temperature (ii) low lubricating oil pressure (iii) engine over speed (iv) engine fails to start (v) full load/maximum load warning 56 earthingearthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required. 57 providing and fixing 25 mm x 5 mm copper strip in 40 mm dia g.i. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re filling etc. as required. 58 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required. 59 providing and fixing 25 mm x 5 mm g.i. strip in 40 mm dia g.i. pipe from earth electrode including connection with g.i. nut, bolt, spring, washer excavation and re filling etc. as required. 60 cablesupplying & fixingof following size xlpe insulated and pvc sheathed aluminium conductorarmoured power cable of 1.1 kv grade conf. to is 7098 (part i)in the following ways etc complete as required. 61 3.5 x 185 sq.mm 62 3.5 x 120 sq.mm 63 3.5 x 95 sq.mm 64 3.5 x 50 sq.mm 65 supplying and making end termination with brass compression gland and aluminium lugs for following size of pvc insulated and pvc sheathed / xlpe aluminium conductor cable of 1.1 kv grade as required. 66 3½ x 185 sq. mm (57mm) 67 3½ x 120 sq. mm (45 mm) 68 3½ x 95 sq. mm (45 mm) 69 3½ x 50 sq. mm (35 mm) 70 misc. civil workproviding and laying in position cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation of pump, dg set etc. including form work etc. as required. 71 excavation of the cable trenches in hard rock not exceeding1.5 meter in width, and lift upto 1.5 meter, including getting out the excavated soil and disposal of excavated soil as directed within a lead of 50 meter. 72 providing brick work (in width 225 mm or more) with f.p.s. bricks of class designation 7.5 in cement mortar 1:4 (1 cement : 4 coarse sand) at all levels. 73 providing 15 mm thick cement plaster of mix 1:4 (1 cement : 4 fine sand) at all levels. 74 demolishing of existing wall i/c reparing with cement plaster and dispose of excavated malba at suitable place out of the site. ...

Delhi Jal Board - Delhi

36872070 press nit no.43, item no.01 (2022 23)cwa (w and s) i procurement of kjeldahl apparatus for cwa(w and s) i division , description –specification( hi media , glassco , borosil ) material of construction ms with powder coated ?nish, operations digestion, distillation and scrubbing in one integrated unit, cooling system & automatic through water coil condenser in higher models, no of samples 6 nos, tubedimension 42x300mm, tubecapacity 250ml(borosilicateglass3.3), process controller 4.3”tfttouch screen controller, mode of operation auto and manual, digestion heating block extruded aluminum block he 30 grade 6063 for 6 samples, digestion heater casted aluminum alloy heater is 4159, digestion heater wattage 1500w, digestion temperature controller pid controller, digestion temperature range 50 degree to 450 degree,digestion temperature accuracy +/ 1%,digestion temperature sensor chromal k type thermo couple upto1200°c, digestion program 5 program and 5 steps,digestion program parameter temperature and time, digestion block insulation ceramic wool,digestion acid fumes removal te?onadapt or fuse to manifold using & outlet connected to the glass suction pump, handle – polyamide,two tier console to place insert rack and manifold rack, digestion tube insert rack stainless steel ss304, digestion manifold rack stainless steel ss304, digestion drip tray stainless steel ss304, exhaust fume condensation in water, scrubber tank stainless steel304,scrubber water leveller – floatswitch, scrubber tank capacity 10 litre,scrubber suction pump giant ?lter pump, distillation expansion vessel glass vessel with te?on insert for alkali addition inlets nippon’s for alkali addition and steam addition, scrubber water re circulation pump 2 magnetic pump with ?ow rate of 18l/min, scrubbing tubing hardnes silicone tube 70±5shorea,temp.resistance 60°c+200°c, real time monitoring of process – yes,no of distillation one at a time,distillation programme 5 program /3 steps, distillation programme steps alkali, reaction delay and process, distillation dosing pump for alkali addition 24 dc motor 500ml/min, distillation steam generator stainless steel ss304 with pressure release valve to back suction of sample, distillation water condenser glass with 2 bulb and coil condenser distillation solenoid valves for steam,re?lling and vent, distillation heater – immersionheater, distillation heater wattage 1500 w, distilled water tank – pvc, distilled water tank capacity 5 lit , distillation reagent tank – pvc, distillation reagent tank capacity 2lit,electrical requirement 230v/50hz/16a, real time monitoring of process – yes, nitrogen recovery 99.5% , nitrogen reproducibility +/ 1%, rsd <1%,lod 1 200mgwith>_0.1mgofnitrogen, total time for process 2.5hours...

Military Engineer Services - Delhi

36094409 miscellaneous b / r works at dipac under age ( i ) ( u ) b / r delhi cantt 10 1 dismantling of wall / ceiling board, any description, includingfillets in any position, complete all as specified. 2 s&f of gl frame work for ceiling comprising of gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with gl cleat and steel expansion fasteners with and including ceiling section ( not exc 1.2 m length ) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including hanger 4mm dia ( upto 1200mm lenth ) made out of gi flat 40x3mm size of 60cm long with expansion hold fastener 12.5mm dia 40mm long complete all as specified and directed. 3 m&l for hspc non asbestos fibre cement building boards 4mm thick, pre primed, self embossed fixed or laid / inserted to gi / aluminium framework with screws complete all as specified and as directed. 4 m&l for solid pvc wall lining of make rajshree plastwood and equivalent consisting of 5mm thick plain colour pvc sheet inclusive of solvent cement and fixing at site on pvc frame as per specifications complete all as specified & directed by the engineer in charge. 5 m&l for 5mm thick pvc sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make pvc frame as per specification complete all as spceifed and as directed. 6 taking down cement plaster, any description from brick or stone walls etc. including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed. 7 m&l for rendering 10 mm thick on brick or concrete surfaces in cement mortar 1:6, finished even & smooth without using extra cement complete all as specified. 8 m&l for preparation of newly untreated plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer with alkali resistant priming paintcomplete all as specified and directed. 9 m&l for rendering 15 mm thick in cement mortar ( 1:4 ) on fair faces of brick work on concrete surfaces using water proofing compound @ 3% by weight of cement finished even and smooth without using extra cement complete all as specified and as directed. 10 supply only integral water proofing compound. 11 m&l for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of primer ( chalk whiting ) complete all as specified and directed. 12 m&l for rendering 5 mm thick in cement mortar ( 1:3 ) on ceilling finish even and smooth without using extra cement complete all as spd and directed. 13 m&l for prepration of newly plastered surfaces on ceiling and applying three coats white wash complete all as specified and as directed. 14 s&f for power coated aluminimum ( minimum thickness of power coating 50 micron ) work for doors, windows, ventilators and partitions ( fixed portions ) with extruded built up standard tubular sections / appripriate z sections and other sections of approved make conforming ti is: 733 and is: 1285, fixing with dash fasteners of required dai and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling c.p brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. 15 hacking out old broken glass ( any thikness, size, quality or description ) from metal frame including punching or drilling out old glazing pins / spring clips and providing and fixing new ones complete all as specified and as directed. 16 s&f for 5.5mm thick sheet glass ordinary quality in square exc 0.50 sqm in each pane complete all as directed. 17 s&f for 3mm thick sheet glass ordinary quality in square n.exc 0.50 sqm in each pane complete all as directed. 18 m&l as in repair for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified and as dirceted. 19 s&f as in repair for aluminium ( extruded section ) body door closer hydraulically regulated, designation no.3, universal type, suaitable for door shutter of 851 to 1000 mm in width and weight between 61 to80 kg and fixed complete all as specified and as directed. 20 s&f as in repair for brass 4 levers mortice lock vertical type, size 100mm complete all as specified and as dirceted. 21 dismantling floor, hearth or wall tiling including cement mortar bedding ( inclbacking ) , removing tilesand rubbish off the premises complete. 22 m&l for non skid ceramic coloured tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and joined in neat cement slurry and pointed in white or colour cement to match colour tiles including 15 mm thick screed bed in cement mortar ( 1:6 ) complete all as specified and directed. 23 m&l for vitrified ceramic coloured tiles 10 mm thick ( square / rectangular ) area of each tile n.exceeding 0.36 sqm in floors etc set and joined in neat cement slurry and pointed in white or colour cement to match colour tiles including 15 mm thick screed bed in cement mortar ( 1:6 ) complete all as specified and directed. 24 demolation of un reinforcedcement concrete in ground floors and pavings n.exc 15cm thick ( below or above groung level ) complete all as specified and as directed. 25 m&l for 75mm thick pcc 1:3:6 type c 2 as in plinth protection complete all as specified and as directed. 26 m&l for applying two coats of synthetic enamel paint over a one coat of red oxide zinc chrome primer on old steel surfaces of any description over 10 cm width or girthcomplete all as specified and directed. 27 m&l for finishing walls with acrylic smooth exterior paint of required shade ( two or more more coat applied @ 1.67 ltr / 10sqm over and including priming coat of exterior primer applied @2.20 kg / 10sqm ) complete all as specified and as directed. 28 dismantling old non gear / gear operated mild steel rolling shutter of any size any position complete all as specified and directed by engr in chrage. 29 s&f for 1.25mm steel rolling shutters, with gear opreated type with bevel gear box and crank handle without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated complete push or manual type complete all as specified and as directed. 30 s&f of safety leaver locks mild steel with 4 leavers for rolling shutters fixing complete all as specified and directede by engr in chrage. 31 m&l for preparation of new steel surface and applying two coats of synthetic enamel paint over a one coat of red oxide zinc chrome primer on new steel surfaces of any description over 10 cm width or girthcomplete all as specified and directed. 32 roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc including neat cement slurry with 3.0 kg of cement per sqm complete all as specified and as directed. 33 m&l for pre / mirror polished machine cut kota stone slab flooring 18 22 mm thick over 15mm thick cement screed base in cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing work where ever required to given high glossy finish complete all as specified and as directed by engr in charge....

Delhi Development Authority - Delhi

35928516 tender for maintenance of various scheme under nazul a / c ii ( ez ) . sh repair of dist. park near samachar apartment mayur vihar ph 1 ( extn. ) in view of g 20 summit. providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level : a ) 1:2:4 ( 1 cement : 2 coarse sand ( zone iii ) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources ) 2 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level : a ) 1:5:10 ( 1 cement : 5 coarse sand ( zone iii ) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources ) 3 centering and shuttering including strutting, propping etc. and removal of form work for : a ) foundations, footings, bases for columns 4 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in foundation and plinth in: a ) cement mortar 1:6 ( 1 cement : 6 coarse sand ) 5 random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 ( 1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size ) upto plinth level with : a ) cement mortar 1:6 ( 1 cement : 6 coarse sand ) 6 stone work ( machine cut edges ) for wall lining etc. ( veneer work ) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand ) including pointing in white cement mortar 1:2 ( 1 white cement : 2 stone dust ) with an admixture of pigment matching the stone shade : ( to be secured to the backing and the sides by means of cramps and pins which shall be paid for separately ) : a ) gang saw cut stone ( i ) 30 mm thick red sand stone 7 raking out joints in lime or cement mortar and preparing the surface for re pointing or replastering, including disposal of rubbish to the dumping ground, all complete as per direction of engineer in charge. 8 pointing on stone work with cement mortar 1:3 ( 1 cement : 3 fine sand ) : a ) raised and cut pointing 9 12 mm cement plaster of mix : a ) 1:6 ( 1 cement: 6 coarse sand ) 10 finishing walls with water proofing cement paint of required shade : a ) new work ( two or more coats applied @ 3.84 kg / 10 sqm ) 11 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : a ) one or more coats on old work 12 finishing walls with water proofing cement paint of required shade : a ) old work ( one or more coats @ 2.20 kg / 10 sqm ) complete. 13 manufacturing, supplying and fixing retro reflective overhead signage boards made up of 4 mm thick acp sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type iii of astm d 4956 01 as approved by engineer in charge, letters, borders etc. as per irc : 67 2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class ii of astm d 4956 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures. the rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer incharge. ( structural frame work including m.s / s.s plate to be provided separately. rectangular area of the sheet only shall be measured for payment ) . ( a ) overhead informatory signage 14 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 15 taking out existing cc interlocking paver blocks from footpath / central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of engineer in charge. 16 laying old cement cocrete interlocking paver blocks of any design / shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineerin charge. ( old cc paver blocks shall be supplied by the department free of cost ) . 17 providing and laying 60mm thick factory made cement concrete paver block of approved shape and colour of m 30 grade made of c&d waste by block making machine with vibratory compaction laid in required pattern and including over 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer in charge. 18 disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by engineer in charge, beyond 50 m initial lead, for all leads including all lifts involved. 19 kota stone slab flooring over 20 mm ( average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) : a ) 25 mm thick...

Northern Railway - Delhi

35759460 supply of 3/4sq drive preset torqe with preset valve3/4sq drive preset torqe with preset valve,3/4sq drive preset torqe with preset valve and safety device made in single piece of alluminium alloy housing to be fixed at 250nm make gedore/ridgid/armstrong/macmaster (detailed specification as overleaf) [ warranty period: 30 months after the date of delivery]...

Airports Authority Of India - Delhi

35428787 construction of combined operational offices of dgca, bcas, aaib, aera and aai at safdarjung airport, new delhi. sh: provision of kitchen equipment fabricating, providing, installing, testing & commissioning of dirty dish landing table of size ( 1500mm x 700mm x 850mm+150 ) , 16 gauge, s.s. top, front turned up 30mm, turned down 50mm & in 12mm. 150mm high rear splash. right side locakable with already exixsting as pre dish washer. top and body secured 38mm x 38mm x 3mm thick s.s. welded angle frame work / hut type welded channel frame work. 200mm round hole for garbage. 4 no. 38mm dia s.s. legs. with s.s. adjustable bullet feet. all sheets to be pre polished plastic coated 304 grade complete as required as per technical specification. 2 fabricating, providing, installing, testing & commissioning of two sink pre wash unit of size 1500mm x 700mm x 850mm + 150mm ( back splash ) , 16 gauge s.s. top. 150mm high rear splash. top and body secured 38mm x 38mm x 3mm thick s.s. welded angle frame work / hut type welded channel frame work. 4 no. 38mm dia. s.s. legs. with s.s. adjustable bullet feet. centre of unit one ( 2 ) no.450mm x 450mm x 300mm deep16 gauge. s.s. sink. 25mm dia s.s. pipe cross bracing welded to legs at rear & both sides. front open. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 3 fabricating, providing, installing, testing & commissioning of pre rinse spray unit of wall mounted hose with overhead spring & spray valve assembly. finger hook of 3 / 8” npt x 18” riser, lever handles with color coded indexes and spring check eternal cartridges. self closing pre rinse spray valve w / rubber bumper & 1.42 gpm flow control spray face. wall mounted. water cold & hot 12mm including accessories deck mounting assembly complete as required as per technical specification. 4 fabricating, providing, installing, testing & commissioning of dishwasher ( hood type ) able to run at two speeds at the capacity of 60 racks per hour. unit suitable to handle 500 x 500 racks . full ss construction.with electronic control.suitable for operation on incoming soft water sanitizing. automaticwater fill. unit should be equipped with rinse pressure pump, drain pump and with rinse agent dispenser. tank should be with rounded edges . should be with self cleaning cycle.200mm high adjustable ss legs including accessories. unit suitable for pass the thermo level, corner installation and complete as required as per technical specification. 5 fabricating, providing, installing, testing & commissioning of unloading table with with 2 nos under pipe shelf of size1100mm x 700mm x 850mm + 150mm, 150mm high rear splash.16 gauge s.s. top. top and body secured 38mm x 38mm x 3mm thick s.s. welded angle frame work / hat type welded channel frame work.4 no. 38mm x38mm s.s. square pipe legs with adjustable bullet feet. full with 2 nos under pipe shelves. all sheets to be pre polished plastic coated 304 grade complete as required as per technical specification.. 6 fabricating, providing, installing, testing & commissioning of clean dish rack 5 tier of size 900mm x 500mm x 1800mm and shelving shall be arranged as shown in the layout plan. 1800mm high overall on ss adjustable feet, constructed of 38mm x 38mm x 16 gauge ss pipe.each to have five shelves at equal distance of18 gauge ss with channels. shelves to be bolted / fixed at each corner. all sheets to be pre polished plastic coated 304 grade complete as required as per technical specification. 7 supply & fixing garbage bin with color as blue / yellow / green, with plastic material capacity of minimum80 ltr. with each set has 3 bin complete as required as per technical specification. 8 fabricating, providing, installing, testing & commissioning of stainless steel drain through grating of size900mm x 700mm x 150mm, grating outer bearing bar frame work of 25mm x 3 mm thick welded construction flushed with finished floor complete installation, grating anti skid , lateral / horizontal cross member of size 25mm x 2.5mm thick, pressure locked & under side common graced to be welded & rest in to s.s. trough. grating with hairline finishing. 150mm deep 18 gauge. s.s. trough channel shape, suitable construction for rest grating. base of trough sloped towards floor drain. provided 100mm dia cutout & integral flange for entry into floor drain on cutout, 100 mm dia. location of floor drain & trough height / size & waste dia to be verify at site complete as required as per technical specification.. 9 fabricating, providing, installing, testing & commissioning of stainless steel pot rackof size ( 1100mm x 600mm x 1650mm ) with four ( 4 ) no stainlless steel pipe shelves. first shelf 150 ( above finished floor ) a.f.f., second 850 a.f.f. third shelf 1450mm a.f.f. & fourth 3 side crossing at 1650mm a.f.f. shelf outer 32mm round / square s.s pipe and inner 25mmround / square. s.s pipe welded to outer tube at 80mm distance. ( 4 ) no. 38mm round / square s.s. pipe. all pipe s.s. 304 grade complete as required as per technical specification. 10 fabricating, providing, installing, testing & commissioning of mobile dirty dish trolley of size 750mm x 600mm x 900mm and 18 gauge. s.s. top channel shape. four ( 4 ) no. 38mm dia uprights on castors. all sides turned up 150mm & handled outside welded to s.s legs. four ( 4 ) no. heavy duty 100mm dia non marking rubberized castors all with brakes. all sheets to be pre polished plastic coated 304 grade complete as required as per technical specification. 11 fabricating, providing, installing, testing & commissioning of sink unitof size ( 450mm x 400mm x 250mm ) unit shall drop in suitable to top counter. internal 350mm x 350mm x 200mm deep 16 gauge s.s. sink, s.s. wall brackets. secured to top with acorn nuts & bolts & bracket secured to wall with anchor fasteners. all sheets to be pre polished plastic coated 304 grade complete as required as per technical specification.. 12 fabricating, providing, installing, testing & commissioning of preparation table size of 1350mm x 700mm x 850mm + 150mm. 150mm high rear splash.16 gauge s.s. top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hut type welded channel frame work.4 no. 38mm x38mm s.s. square pipe legs with adjustable bullet feet. full with 3 side cross bracing 25 mm round pipe. all sheets to be pre polished plastic coated 304 grade complete as required as per technical specification. 13 fabricating, providing, installing, testing & commissioning of two sink vegetable washing unit of size 1250mm x 700mm x 850mm + 150mm, 16 gauge s.s. top. 150mm high rear splash.top and body secured 38mm x 38mm x 3mm thick s.s. welded angle frame work hut type welded channel frame work. 4 no. 38mm dia. s.s. legs. with s.s. adjustable bullet feet. centre of unit one ( 2 ) no.500mm x 500mm x 300mm deep16 gauge. s.s. sink. 25mm dia s.s. pipe cross bracing welded to legs at rear & both sides. front open. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 14 supply, installing, testing & commissioning ofvegetable cutter made up of aluminium alloy and s / s construction with ventilated motor for continuous operation, suilable for easy processing for soft products like moz zarella cheese. safe operation with interlock switches on product pusher, with 6 blades, lid and collect ing tray. large number of discs available for every purpose with max power515w&0.7 hp power source 1ph / 3ph disc revolutions r.p.m. 300 complete as required as per technical specification. ( model tm2 all / inox or equivalent ) 15 supply, installing, testing & commissioning of min 900 w mixer, grinder with most powerful motor with double ball bearingswith 22000 rpm, chutney jar as400 ml, liquidizing jar with minimum 1.5 l , minimum 3 nos. of jars withplastic body, 230 240 v acthee no. ( 03 ) speed settingwith maximum power consumption 900 w complete as required as per technical specification. ( make sujata or equivalent ) 16 fabricating, providing, installing, testing & commissioning of pulverizer, runs easily. the dry / wet stainless steel body, 24 hours running capacity, easy to maintain, attractive in finish, special air cooling system for motorwith minimum 2 hp and complete as required as per technical specification. 17 fabricating, providing, installing, testing & commissioning of potato peeler, cap 10kg, having overall. potato peeler shall be of vertical design suitable for mounting on thefloor. machineshallbedividedintwo sections, top peelingassembly and the bottom for motor drive housing, all made of stainless steel as per technical specification with 1.0 hp mtor and complete as required as per technical specification. all sheets to be pr polished plastic coated 304 grade. 18 fabrication, installing, testing & commissioningatta kneading machine of minimum 25 kg atta made up ofheavy duty cast iron with gear box mounted on the top the mixing bowl of ss sheet min 18 swg with handle the dough kneading machine is comes with single attachment the machine is operated electrically with min 2 hp motor on single phase complete as required as per technical specification.. 19 fabricating, providing, installing, testing & commissioning of work table with sink unit of size 1350mm x 600mm x 850mm + 150mm , 16 gauge s.s. top. 150mm high rear splash. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hut type welded channel frame work, 4 no. 38mm dia. s.s. legs. with s.s. adjustable bullet feet. centre of unit one ( 1 ) no.400mm x 400mm x 250mm deep16 gauge. s.s. sink. with one under shelf 18 guase. welded to legs at rear & both sides. front open.all sheets to be pre polished plastic coated 304 grade complete as required as per technical specification. 20 fabricating, providing, installing, testing & commissioning of masala grinder ( tilting ) of conventional 10 liters capacity wet grinder with twin roller construction minimizes spillage with vertical construction to occupy less space unit with1.0 hp motor with on single phase, wet grinder in stainless steel wired including accessories power chord and complete as required as per technical specification. 21 fabricating, providing, installing, testing & commissioning of work table with sink unit of size 1800mm x 700mm x 850mm + 150mm , 16 gauge s.s. top. 150mm high rear splash. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hut type welded channel frame work.. 4 no. 38mm dia. s.s. legs. with s.s. adjustable bullet feet.centre of unit one ( 1 ) no.500mm x 500mm x 300mm deep16 gauge. s.s. sink.with one under shelf 18 guase welded to legs at rear. all sheets to be pre polished plastic coated 304 grade complete as required as per technical specification.. 22 fabricating, providing, installing, testing & commissioning of two door under counterof size 1400mm x 700mm x 850mm. 18 gauge ss top / ss 304 interior and exterior. 150mm high rear splash. all sides turned down 50mm & in 12mm. top and body secured to 12 / 25mm x 100mm x 25 / 12mm, 1.2 mm thick s.s. hut type welded channel frame work. underside of the top shall be sound proof, 2nos. ss removable & adjustable shelves. 2 nos. sufring doors with insulation. accommodates 1 / 1 g.n pan.ambient temperature 43 deg c.internal temp 2 deg c to 4 deg c, air cooled, digital read out thermometer, cord with time delay, auto start, forced draft cooling. 38mm dia s.s. tubular legs, with s.s. adjustable bullet feet, 50mm thick p.u. foam on all sides, drip tray with heating. ( for condensate water evaporation ) . all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 23 fabricating, providing, installing, testing & commissioning of work table with 2 under size of 1350mm x 700mm x 850+150mm, 150mm high rear splash, 16 gauge s.s. top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.4 no. 38mm x38mm s.s. square pipe legs with adjustable bullet feet. full with 18 gauge s.s. bottom shelves. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 24 fabricating, providing, installing, testing & commissioning of gas operated s s cladded mobile tandoor of size 750mm x 750mm x 850+150mm, 150mm high rear splash, 16 gauge s.s. top, top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work, exterior 18 gauge s.s. cladding, interior 18 gauge 304 grade. m.s. cladding, 40mm thick mineral wool insulation, front s.s. ash removable opening with shutter, ( 4 ) no. heavy duty 100mm dia non marking rubberized castors all with brakes, 2 no. top sheets to be prepolished plastic coated s.s and complete as required as per technical specification. 25 fabricating, providing, installing, testing & commissioning of work table with 2 under size of 600mm x 750mm x 850++150mm, 150mm high rear splash, 16 gauge s.s. top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hut type welded channel frame work.4 no. 38mm x38mm s.s. square pipe legs with adjustable bullet feet. full with 18 gauge s.s. bottom shelves. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 26 fabricating, providing, installing, testing & commissioning of two burner range with under shelf of size ( 1300mm x 750mm x 850mm+150mm ) . 16 gauge s.s. top. 150mm high rear splash, back splash to be covered with 20 gauge s.s. sheet.top and body secured 38mm x 38mm x 3mm & 25mm x25mm thick m.s. welded angle frame work, hat type welded channel frame work. exterior 18 gauge s.s. cladding. built in pressure controller regulator. 38mm x 38mm x 16 gauge s.s. square pipe legs with s.s. adjustable bullet feet. 25mm x 25mm s.s. square pipe under shelf. 2 no. 400mm x 400mm cast iron grate ( removable ) . two ( 2 ) no.22 gauge s.s. drip tray with integral handle. auto ignition. two ( 2 ) no.h.p burner rated @70, 000 b.t.u’s / hr. with pilot lamp. 100mm setback body / legs for gauges pipe routing. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 27 fabricating, providing, installing, testing & commissioning of work table with 2 under size of 900mm x 750mm x 850++150mm, 150mm high rear splash, 16 gauge s.s. top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.4 no. 38mm x38mm s.s. square pipe legs with adjustable bullet feet. full with 18 gauge s.s. bottom shelves. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 28 fabricating, providing, installing, testing & commissioning of single sink unit with one underself crossing of size 600mm x 700mm x 850mm + 150mm , 16 gauge s.s. top. 150mm high rear splash. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.. 4 no. 38mm dia. s.s. legs. with s.s. adjustable bullet feet. centre of unit one ( 1 ) no.400mm x 400mm x 250mm deep16 gauge. s.s. sink. 25mm dia s.s. pipe cross bracing welded to legs at rear & both sides. front open. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 29 fabricating, providing, installing, testing & commissioning of exhaust hood of size 2900mmx 900mm x 500mm external and internal parts to be manufactured in ss 202, 18gauge welded body construction, removable 22 gauge s.s v section, measuring 510*510*50 mm thick, in full length with bottom of filters set in continuous channel, grease gutter on rear and side in each piece, as per requirement, of flushed glass lights.all sheets to be pre polished plastic coated 202 grade complete as required as per technical specification. 30 fabricating, providing, installing, testing & commissioning of work table with sink unit of size 1350mm x 700mm x 850mm + 150mm , 16 gauge s.s. top. 150mm high rear splash. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.. 4 no. 38mm dia. s.s. legs. with s.s. adjustable bullet feet. centre of unit one ( 1 ) no. 4500mm x 450mm x 300mm deep16 gauge. s.s. sink.with one under shelf 18 guase welded to legs at rear. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 31 fabricating, providing, installing, testing & commissioning of idli steamer of min 54 idlies operated the unit will be double walled completely out of 18 swg. ss sheet with insulation in between. the idly trays to be out of 18 swg. ss with 16 swg. aluminimum drip tray under each ss idli tray. the unit will have one door. the doors will also be insulated with steam effective rubber gasket beading ½ “ ss valve control will be provided for steam control and safety valves will be provided in the steam pipe. the steamer is operated on a low pressure steam boiler fitted underneath. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 32 fabricating, providing, installing, testing & commissioning of work table with 2 under size of600mm x 600mm x 850++150mm, 150mm high rear splash, 16 gauge s.s. top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.4 no. 38mm x38mm s.s. square pipe legs with adjustable bullet feet. full with 18 gauge s.s. bottom shelves. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 33 fabricating, providing, installing, testing & commissioning of work table with under size of1350mm x 700mm x 850+150mm, 150mm high rear splash, 16 gauge s.s. top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.4 no. 38mm x38mm s.s. square pipe legs with adjustable bullet feet. full with 18 gauge s.s. bottom shelves. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 34 fabricating, providing, installing, testing & commissioning of two door under counter refer of size 1400mm x 700mm x 850mm. 18 gauge ss top / ss 304 interior and exterior. 150mm high rear splash. all sides turned down 50mm & in 12mm. top and body secured to 12 / 25mm x 100mm x 25 / 12mm, 1.2 mm thick s.s. hat type welded channel frame work. underside of the top shall be sound deadened. 2nos. ss removable & adjustable shelves. 2 nos. sufring doors with insulation. accommodates 1 / 1 g.n pan.ambient temperature 43 deg c.internal temp 2 deg c to 4 deg c, air cooled, refrigerant kirloskar / techumseh with complete unit ( gas: r 134 a ) digital read out thermometer, cord with time delay auto start, forced draft cooling. 38mm dia s.s. tubular legs, with s.s. adjustable bullet feet, 50mm thick p.u. foam on all sides, drip tray with heating. ( for condensate water evaporation ) . all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 35 fabricating, providing, installing, testing & commissioning of work table with 2 under size of700mm x 750mm x 850++150mm, 150mm high rear splash, 16 gauge s.s. top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.4 no. 38mm x38mm s.s. square pipe legs with adjustable bullet feet. full with 18 gauge s.s. bottom shelves. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 36 fabricating, providing, installing, testing & commissioning of single sink unit with 3 side crossing of size 600mm x 700mm x 850mm + 150mm , 16 gauge s.s. top. 150mm high rear splash. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.. 4 no. 38mm dia. s.s. legs. with s.s. adjustable bullet feet. centre of unit one ( 1 ) no.400mm x 400mm x 250mm deep16 gauge.s.s. sink. 25mm dia s.s. pipe cross bracing welded to legs at rear & both sides. front open. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 37 fabricating, providing, installing, testing & commissioning of work table with 2 under size of 700mm x 750mm x 850+150mm, 150mm high rear splash, 16 gauge s.s. top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.4 no. 38mm x38mm s.s. square pipe legs with adjustable bullet feet. full with 18 gauge s.s. bottom shelves. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 38 fabricating, providing, installing, testing & commissioning of work table with under size of 1350mm x 700mm x 850mm. 16 gauge s.s. top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.4 no. 38mm x38mm s.s. square pipe legs with adjustable bullet feet. full with 18 gauge s.s. bottom & middle shelves. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 39 fabricating, providing, installing, testing & commissioning of gas operated chapatti plate with pufferof size ( 1500mm x 750mmx850mm+150mm ) . 16mm thick m.s. griddle plate with front.gutter & s.s. grease drawer. plate and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work. exterior 20 gauge. s.s. cladding. built in pressure controller regulator. 38mm x 38mm x 16 gauge s.s. square pipe legs withadjustable bullet feet. 25mm x 25mm s.s. square pipe under shelf. four ( 4 ) no. “v” type h.p. burner with pilot lamp. 100mm setback body / legs for gauges pipe routing. smooth plate complete as required as per technical specification. 40 fabricating, providing, installing, testing & commissioningof mobile chapati collection trolley of size 600mm x 750mm x 850mm and 14 gauge. s.s. top channel shape. four ( 4 ) no. 38mm dia uprights on castors. two ( 2 ) no 18 gauge s.s pan with all sides turned up 100mm & hemmed outside welded to s.s legs. four ( 4 ) no. heavy duty 125mm dia non marking rubberized castors all with brakes. under sides of top shall be reinforced with 25 x 100 x 25 16 gauge s.s inverted channel including accessories.all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 41 fabricating, providing, installing, testing & commissioning of griddle plateof size ( 1100mm x 750mmx850mm. 16mm thick m.s. griddle plate with front.gutter & s.s. grease drawer. plate and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hut type welded channel frame work. exterior 20 gauge. s.s. cladding. built in pressure controller regulator. 38mm x 38mm x 16 gauge s.s. square pipe legs with adjustable bullet feet. 25mm x 25mm s.s. square pipe under shelf. three ( 2 ) no. “v” type h.p. burner with pilot lamp. 100mm setback body / legs for gauges pipe routing. smooth plate complete as required as per technical specification. 42 fabricating, providing, installing, testing & commissioning of work table with 2 under size of 700mm x 750mm x 850+150mm, 150mm high rear splash, 16 gauge s.s. top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.4 no. 38mm x38mm s.s. square pipe legs with adjustable bullet feet. full with 18 gauge s.s. bottom & middle shelves. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 43 fabricating, providing, installing, testing & commissioning of exhaust hood of size 4210 mm x 2100mm x 500mm external and internal parts to be manufactured in ss 202, 18gauge welded body construction, removable 22 gauge s.s v section, measuring 510*510*50 mm thick, in full length w / bottom of filters set in continuous channel, grease gutter on rear and side in each piece. all sheets to be pre polished plastic coated 202 grade complete as required as per technical specification. 44 fabricating, providing, installing, testing & commissioning of 320 ltr two door vertical referigerator of size 720mm x 750mm x 2050mmexterior / interior 20 gauge s.s. cladding. 50mm thick puff insulation. body secured to 12 / 25mm x 100mm x 25 / 12mm 22 guase thick s.s. welded channel frame work.two ( 2 ) nos. half size insulated self closing type s.s doors, complete with handle, gasket & locking arrangement hinged at front, three ( 3 ) wire shelves removable s.s welded wire. ambient temperature 43 deg c. internal temp is 0 deg to + 4deg celsius. air cooled referigerant with complete unit ( gas: r 134 a ) digital read out thermometer, cord with time delay auto start, forced draft cooling. 38mm dia s.s. tubular legs, with s.s. adjustable bullet feet, 50mm thick p.u. foam on all sides, drip tray with heating. ( for condensate water evaporation ) . all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 45 fabricating, providing, installing, testing & commissioning of work table with 2 under size of1200mm x 600mm x 850+150mm, 150mm high rear splash, 16 gauge s.s. top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.4 no. 38mm x38mm s.s. square pipe legs with adjustable bullet feet. full with 18 gauge s.s. bottom & middle shelves. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 46 supply, installation, testing, commissioning of table top weighing scale with follwing features; operating temperature: 0 to 50 deg c accuracy:2 g weighing capacity:20 kg warranty:1 year display type: digital battery voltage:6 v frequency: 50 hz material:stainless steel power supply: mains & battery operated complete as required as per technical specification. 47 fabricating, providing, installing, testing & commissioning of ss storage rack 5 tier of size 900mm x 500mm x 1800mm and shelving shall be arranged as shown in the layout plan. 1800mm high overall on ss adjustable feet, constructed of 38mm x 38mm x 16 gauge ss pipe.each to have five shelves at equal distance of18 gauge ss with channels. shelves to be bolted / fixed at each corner. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 48 fabricating, providing, installing, testing & commissioning of mobile ingredient bin ( atta maida bin ) of size ( 450mm x 600mm x 700mm ) . 18 gauge welded body constructions.all corners coved 20mm radius. 18 gauge s.s. half open able centre hinged lid with integral handle. s.s. hat type channel base. four ( 4 ) no. 100mm high castor two with brakes. rubber corner bumper on all four sides. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 49 fabricating, providing, installing, testing & commissioning of ss dunnage rack of size 1200mm x 600mm x 200mm with sectional 18 guage ss rods at equal distance, 500 high overall on ss adjustable feet, constructed of 38mm x 38mm x 16 gauge ss pipe. shelves to be bolted / fixed at each corner. all sheets to be pre polished plastic coated 304 grade complete as required as per technical specification. 50 fabricating, providing, installing, testing & commissioning of platform weighing scale 600mm x 600mm x 900mm freestanding electronic digital scale, s.s weighing platform of size approx. 550 mm w x 550 mm. unit suitable to weigh up to 300 kgs with 40 gms increments, digital pillar mounted display, rechargeable battery backup , bottom structure is metal powder coated rust free stainless steel platter. electrical power 0.03 kw in 220 50 1ph including accessories power cord. rs 232 serial interface and complete complete as required as per technical specification. 51 fabricating, providing, installing, testing & commissioning of onion / potato binof size 750mm x600mm x900mm, 25mm x 25mm 14 gauge stainelss steel outer frame work, have caster arrangements with lock andhave proferation all around, have a false bottom, front, top rear & sides 4mm & 6mm thick stainelss steel wire mesh. in rectangular form with hinged lid on the top with locking arrangement. the stainless steel sheet will be perforated all over to dip potatoes and onion airy and fresh. the bins will be mounted on four nos. heavy castor wheels providing and placing in position of onion potatao storage bins complete as required as per technical specification. 52 fabricating, providing, installing, testing & commissioning of ss vegetable rack 5 tier of size 900mm x 500mm x 1800mm and shelving shall be arranged as shown in the layout plan. 1800mm high overall on ss adjustable feet, constructed of 38mm x 38mm x 16 gauge ss pipe.each to have five shelves at equal distance of18 gauge ss with channels. shelves to be bolted / fixed at each corner. all sheets to be pre polished plastic coated 304 grade complete as required as per technical specification. 53 supply , installation, testing & commissioning of 400 ltrs deep freezer operable withac 230 v, 50 hz, temparature range < 18 degree c, puf thickness 60 mm, with uv grade plastic material for long lasting appearnce, door lock arrangement, anti corrosive body, caster wheel for easy mobility , spring loaded hinges for effortless usage with complete as required as per technical specification. 54 fabrication , installation and testing of 9 compartment ms staff locker 2000mmx 600mmx100 mm overll size with compartmentalised shelf complete as required as per technical specification. 55 fabricating, providing, installing, testing & commissioning of plat pickup counter of size 1100mm x 700mm + 300mm x 850mm. 18 guase top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hut type welded channel frame work. 4 no. 38mm dia. s.s. legs with adjustable bullet feet. full width 18 gauge s.s. bottom shelves. 3 side covering 20 guase, all sheets to be pre polished plastic coated 304 grade s.s. and complete as required as per technical specification. 56 fabricating, providing, installing, testing & commissioning of hot bainmarie of size 2100mm x 675mm + 300mm x 850mm. ( 6 nos. 1 / 1 gn pan 5 nos hot & 1 no. normal temp. ) 18 guase top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work. 4 no. 38mm dia. s.s. legs with adjustable bullet feet. full width 18 gauge s.s. bottom shelves. 3 side covering 20 guase, bain marie double walled insulated puf type glass wool. electric load: heating element shall be 3 kw 440 v 3ø. there shall be water inlet of 12mm dia and waste connection with valve of 38mm dia.all sheets to be pr polished plastic coated 304 grade s.s and complete as required as per technical specification. 57 fabricating, providing, installing, testing & commissioning of ambiant bain marie of size 800mm x 700mm + 300mm x 850mm. ( 2 nos. 1 / 1 gn pan ) 18 guase top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work. 38mm dia s.s. tubular legs, with s.s. adjustable bullet feet, all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 58 providing, installing, testing & commissioning of display unit ( refrigeration ) of size ( 1200mm x 700 mm x 1300mm ) 20 gauge ss 304 body. internal temp +3 deg c to + 14 deg c. ( suitable temp for pastry & cake ) . three ( 3 ) no. full length glass shelf. all interiors to be of s. s. forced draft cooling. light arrangement as per id . with humidity control. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 59 supply, installation, testing & commissioining of visi cooler with pre coated metallic inner and outer cabinet for durability and enhanced cooling , castor wheels for easy movement, corrosion free aluminium door frame, led lighting for better visibility, adjustable shelves, eco friendly refrigerant complete as required as per technical specification. 60 fabricating, providing, installing, testing & commissioning of work table with 2 under size of 1600mm x 600mm x 850+150mm, 150mm high rear splash, 16 gauge s.s. top. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.4 no. 38mm x38mm s.s. square pipe legs with adjustable bullet feet. full with 18 gauge s.s. bottom & middle shelves. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 61 fabricating, providing, installing, testing & commissioning of work table with sink unit of size 1350mm x 700mm x 850mm + 150mm , 16 gauge s.s. top. 150mm high rear splash. top and body secured 38mm x 38mm x 3mm thick m.s. welded angle frame work, hat type welded channel frame work.. 4 no. 38mm dia. s.s. legs. with s.s. adjustable bullet feet.centre of unit one ( 1 ) no. 4500mm x 450mm x 300mm deep16 gauge. s.s. sink.with two under shelf 18 guase welded to legs at rear. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 62 fabricating, providing, installing, testing & commissioning of salamander ( wall mounted ) of size 750 mm x 400 mm x 350 mm.s.s. body construction. complete with concealed fuel riser. unit shell be wall mounted. s.s. grid to be self spring adjustable at 3 locking positions with s.s. front & back. outer and internal 20 gauge s.s. cladding.suitably insulated, heating elements clamped on underside of top. high heat broiling thermostat. on off controls on right. electric power: 3.0 kw. power supply: 220.50.1hp including accessories power cord with plugincluding accessories. all sheets to be pr polished plastic coated 304 grade complete as required as per technical specification. 63 supply & insttalation of 20 ltrs. solo microwave oven with maximum output power 700 wattsingle phase 240v operable with reheating feature complete as required as per technical specification. 64 supply & installation of1600w induction platewith 7 pre defined cooking, soft touch control with digital display, higher rated igbt, vessel sensor & auto cut off, timer 0 4 hrs, efficient cooling system function complete as required as per technical specification. 65 supply, installation, testing , commissioning of minimum 195 litres refrigerator toughened glass shelves 5 star energy rating reciprocatory compressor built in stabilizer removable gasket complete as required as per technical specification. ( 66 supply, installation, testing , commissioning of jumbo size twin flying insect killer made up of mild steel with 2 nos. 40w lamps with minimum size of 50x 6.5x 20 covering area upto 1000 sqft , suitable tocollect the dead insectsin the catchment tray at the bottom for easy disposal complete as required as per technical specification. 67 supply, installation, testing and commissioning of air curtain of 1.2 mtr. ( approx. ) length having abs body, single speed, continuous rating motor & maximum noise level 55 db suitable for operating on 230v +5%, 50 hz ac supply including provision of control switchgears for interlocking / synchronizing the operation of sliding doors, etc.as required and as per enclosed specification. note: air curtain will be operational only when sliding gates are in open position....

Northern Railway - Delhi

35006401 supply of aluminum alloy cast arm rest with pu cushion green colour along with aluminum alloy bracket for shatabdi coaches as per drawing no judw / mech / 14 649 make sutlej, sukaratractor, sahay enterprisesaluminum alloy cast arm rest with pu cushion green colour along with aluminum alloy bracket for shatabdi coaches as per drawing no judw / mech / 14 649 make sutlej, sukaratractor, sahay enterprises, aluminum alloy cast arm rest with pu cushion green colour along with aluminum alloy bracket for shatabdi coaches as per drawing no judw / mech / 14 649 make sutlej, sukaratractor, sahay enterprises or similar....

Delhi Technological University - Delhi

34740855 supply of the following items 1. duplex grade stainless steel plate grade 2205 dim: 100x60x10 mm duplex grade stainless steel plate grade 2205 dim: 100x60x6 mm 2. en 19/ aisi 4140 plate dim: 100x60x10 mm en 19/ aisi 4140 plate dim: 100x60x6 mm 3. ernicrmo 3 (in 625) filler wire spool specification: 1.2 mm dia. 10 kg 4. er 2209 (dss) filler wire spool specification: 1.2 mm dia. 15 kg 5. butane gas can with a torch weight: 250 gm 6 aluminium alloy 6061 t6 solid rod bar diameter=80 100mm 7 tib2 micro sized powder mean particle size=14 20 μm 8 la2o3 nano sized powder mean particle size=40 50 nm 9 graphite crucible specifications cuboid shaped with outer length=130mm outer breadth=80mm outer height=65mm overall thickness=15mm...

Northern Railway - Delhi

34476260 supply of aluminium alloy arm rest assemblyaluminium alloy arm rest assembly, aluminium alloy arm rest assembly with pu pad for executive chair car as per drawing no 3 skt 48 , item a only for vande bharat express....

Northern Railway - Delhi

34476257 supply of alluminium alloy arm rest assemblyalluminium alloy arm rest assembly, alluminium alloy arm rest assembly with pu pad as per drg no. 3 skt 48 item a only for chair car for vande bharat express...

Northern Railway - Delhi

34475555 supply of aluminium alloy foot rest assemblyaluminium alloy foot rest assembly, aluminium alloy foot rest assembly for executive chair car as per drg. no. 3 skt 48, item c type 1 for vande bharat express....

National Institute Of Immunology - Delhi

32736525 tender for repairing of cooling towers at nii, new delhi dismantling and removal of defective cooling towers top sheet, fan casing, fan assembling, motor, cables and defective angles etc and their disposing etc as per site requirements. supply and fixing of 3mm thick frp top sheet app. 15ft.x12ft. including repairing etc as per site requirements. supply and fixing of heavy duty gi supporting angle 40x40mmx5mm including welding etc as per site requirements. supply and fixing of gi coted nut bolts washers etc as per site requirements. supply and fixing of aluminium alloy fan assembly complete set, hub and blades with statically balanced size 1200mm x 6 blade including fixing of motors etc as per site requirements. buy back of old and dismantled items...

Ministry Of Tourism - Delhi

32638495 bids are invited for aluminium and aluminium alloy bare foil for food packaging is:15392 (q3) , plastic stretch wrap film (q4)mse total quantity : 925...

Ministry Of Defence - Delhi

31728045 bids are invited for surgical isolation or surgical masks ( q3 ) , centrifuge tubes ( q3 ) , laboratory vials ( q3 ) , universal pipette tips ( q3 ) , surgical gloves is 4148 ( q3 ) , disposable syringes as per is: 10258 & is: 10258 ( q4 ) , sterile gauze pads or swabs ( q3 ) , ecg electrodes ( q3 ) , aluminium and aluminium alloy bare foil for food packaging is:15392 ( q3 ) , alcohol based handrub / hand sanitizer ( q3 ) , surgical dressing trays ( q3 ) , glacial acetic acid ( q3 ) , blades surgical detachable ( q3 ) , hydrochloric acid as per is:265 ( q3 ) , sodium hydroxide is:252 ( q3 ) , sodium chloride, analytical reagent as per is:4408 ( q3 ) total quantity : 75316...

Ministry Of Defence - Delhi

31724136 bids are invited for aluminium and aluminium alloy bare foil for food packaging is:15392 (q3) , tissue papers is 14461 (q4) total quantity : 330...

Ministry Of Tourism - Delhi

31600624 bids are invited for aluminum and aluminum alloy bare foil for food packaging is:15392 ( q3 ) total quantity : 1200...

Department Of Health And Family Welfare - Delhi

30969085 bids are invited for aluminum and aluminum alloy bare foil for foodpackaging is:15392auto extension if any seller submits price in last 15 minutes, the rawill be auto extended by 15 minutes. ( a maximum of100 times ) mse total quantity : 1000...

Delhi Jal Board - Delhi

30626980 bids are invited for item1 electrical gloves ,type of gloves 1 composition natural rubber , construction –latex, make: vidyut/ crystal. , item2 strecher aluminiumfor emergency and resuce operations ,size 205x53x13 , item3 resuscitator/rebreathingbag ,material silicon rubber , item4 torch ,body material aluminium alloy ,rated power 5watt ,maximum beam distance 279 meter,battery backup 2hr,battery capacity 3200 3400mah , item5 life safer ring ,inner diameter 400mm ,outer dia 800mm , item6 first aid kit , item7 safety belt, make: karam/ udyogi. , item8 safety industrialgloves for mechanical purpose , item9 safety shoes , make: allen cooper/jcb/liberty , item10 hand senitizer ,pack size 5000 ml (5 litre ) in 1 bottle , item11 conical cone (barrier cone ) ,shape of base square ,material of cone hdpe , , item12 caution tape total quantity : 1...

Ministry Of Defence - Delhi

30471378 bids are invited for laboratory beakers is:2619 (q4) , laboratory graduated cylinders is 878 (q3) , surgical gloves is 4148 (q3) , isopropyl alcohol (2 propanol) (q3) , glass bottles (q3) , filter paper (q4) , trizol reagent (q3) , pcr grade water (q3) , chloroform (q3) , blotting paper (q3) , aluminium and aluminium alloy bare foil for food packaging is:15392 (q3) , universal pipette tips (q3) , funnel (q3) ,microcentrifuge tubes (q3) , surgical isolation or surgicalmasks (q3) , manual single channel air displacementpipetters or micropipette (q3) , freezing / cryo box (q3) ,pcr tubes (q3) , tris(hydroxymethyl)aminomethane (q3) ,pcr master mix (q3) total quantity : 83597...

Indian Army - Delhi

30427151 supply of stores modified reel strapping co 1580x1000mm long assy ( drg no. im 0637 / 1 / b, im 0638 / 1 / a ) , aluminium alloy special shape full planks size 200x1000mm for atw cl 12 ( drg no. impd 1927 ) , drift pin ( drg no. impd 1031 ) , common spike, hexagonal 20 mm a / f 750mm steel ( drg no. impd 1926 / a ) , tie bar ( drg no. impd 1924 / a ) , nut plain sqr m 8x10mm long steel ( drg no. impd 1925 / a ) , aluminum alloy specialshaped sec 200x330mm ( connectors ) ( drg no. impd 1923 / a ) , spnr ojde 24x27 ( drg no. is 2028 ) , screw driver flat point 200mm long ( drg no. is 844 ) , crow bar round chisel and hammer end 25mmx1525mm ( drg no. is 704 ) , washer spring steel type d zink plate m 12 ( drg no. is 3063 ) , nut plain steel wing zinc plated m 12 ( drg no. is 2636 ) , aluminium alloy special shaped section 203 x 1670 mm long, half plank ( drg no. impd 1120 ) , planks for atw cl 30 ( drg no. impd 1120 ) , screw set 20 x 102 mm ( drg no. impd 1026 ) , spanner ojde 19 x 22 ( drg no. is 2028 ) , sling ( i ) multiple logs having two chains with d shackles ( drg no. impd 1029 ) , pin for fdb ( drg no. impd 1838 ) , panel deck aluminium for mgs cl 50 ( drg no. imsa 0228 ) ...